Electrolux FHWC3655LSA Manuel d'utilisation et d'entretien - Page 8

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et d'entretien pour {nom_de_la_catégorie} Electrolux FHWC3655LSA. Electrolux FHWC3655LSA 13 pages. 30 and 36 free-standing range hood
Également pour Electrolux FHWC3655LSA : Manuel d'utilisation et d'entretien (13 pages), Manuel d'utilisation et d'entretien (13 pages)

Imprimer la page
Electrolux FHWC3655LSA Manuel d'utilisation et d'entretien
8
Installing the hood
fig.
Long
screws
Wood
screws
1.5"
Desired range hood distance above a
36" high cook top
8 Feet
A*
26"*
27-5/16"
3
27"*
28-5/16"
3
28"*
29-5/16"
3
29"*
30-5/16"*
3
30"*
31-5/16"*
3
31"*
32-5/16"*
3
32"*
33-5/16"*
3
33"
34"
35"
*
: with 10' Extension chimney kit FHW10X55LS
1
(14) (not supplied). Please call Frigidaire at
1.800.944.9044 to order this kit.
*
: "
2
Dimension A
from cook top to where the bottom screw mounting
holes would be located.
*
: Recommended mounting height
3
*
: Recirculation Kit cannot be installed.
4
Step 2:
• Install the range hood (1) either with wood screws
or long screws, depending on the wall type:
Wall type
Wood
Brick/Concrete
GB
Ceiling
0.86"
2.95"
5.1"
15.67"
5.9"
8.3"
15.98"-FHWC3055L
Dimension
23.86"-FHWC3655L
Wall
(see table)
Ceiling height
9 Feet
10 Feet *
A*
2
2
28-5/16"
29-5/16"
29-5/16"
30-5/16"
30-5/16"
4
31-5/16"
31-5/16"
4
32-5/16"
32-5/16"
4
33-5/16"
33-5/16"
4
34-5/16"
34-5/16"
35-5/16"
35-5/16"
36-5/16"
36-5/16"
" in the chart represents the height
Required screws
4 wood screws (11)
4 long screws (8)
• Insert 2 screws (8 or 11) in the top location, but
do not fully insert the screws (fig.
range hood (1) to the wall and tighten the screws.
Insert and tighten the 2 remaining screws on the
bottom location of the range hood (fig.
• Attach the collar (5) to the range hood (1). Secure
with 2 short screws (8) (fig.
fig.
A
fig.
fig.
0.08"
NOTE
Sometimes, sponge tape covers the holes. If the
1
holes are located behind the sponge tape, simply
A*
2
insert the screw through the sponge tape.
Step 3:
• Mount upper and lower brackets (3, 4) on the
wall. Secure with the remaining 4 sets of long
screws (8). The notches of the lower bracket
should be facing up towards the ceiling (fig.
• Attach the exhaust duct. In the example below
a round metal duct furnace pipe has been used.
The airtight connection of the exhaust duct
should then be improved with a duct tape. This
ensures tight fit and that no grease vapors will
escape from the duct (fig.
fig.
). Mount the
/
).
).
fig.
0.08"
fig.
) .
) .
fig.