Electrolux RH36WC40GS Manuel d'installation, d'utilisation et d'entretien - Page 11

Parcourez en ligne ou téléchargez le pdf Manuel d'installation, d'utilisation et d'entretien pour {nom_de_la_catégorie} Electrolux RH36WC40GS. Electrolux RH36WC40GS 19 pages. 36" under-cabinet hood
Également pour Electrolux RH36WC40GS : Catalogue des pièces d'usine (4 pages), Spécifications des produits (2 pages)

Imprimer la page

Electrolux RH36WC40GS Manuel d'installation, d'utilisation et d'entretien

1. Filters

Outside r

Outside rear exhaust

Outside r

ear exhaust

(Horizontal duct– 3 1/4"x 10" Rectangular)

• • • • •

Use the diagram or the hood as a template

and mark the locations on the cabinet for ductwork,

electrical wiring and keyhole screw slots.

Wood shims (recessed

bottom cabinets only)

Cabinet front

Horizontal duct

3 3/4"

access hole

Cabinet

5 1/4"

bottom

13 15/16" (30" Hood)

16 15/16" (36" Hood)

Center line

Hood mounting screws (4)

Recir

culating

Recir

Recirculating

Recir

culating

Use the hood as a template and mark the locations

on the cabinet for the electrical wiring and keyhole

screw slots.

Since the hood is to be recirculated (not to be vented

outside), do not cut out any vent openings in the wall

or cabinet bottom.

Step 9

Choose Venting Option

Choose V

enting Option

Choose V

enting Option

The hood can be set to vent outside or to recirculate

air back into the kitchen.

Set for

outside venting

recirculating

Stop tab

Hood shown Lying upside down

The plastic vent lever is located near the center of the

hood opening.

T T T T T o vent to the outside,

o vent to the outside, make sure the plastic vent

o vent to the outside,

HORIZONT

lever is in the HORIZONT

HORIZONTAL

HORIZONT

AL position (flat against the

metal top of the hood).

T T T T T o r

o r

o recir

o r

ecir

ecirculate air into the kitchen,

ecir

culate air into the kitchen,

culate air into the kitchen, make sure the

VER

plastic vent lever is in the VER

VERTICAL

VER

against the plastic blower housing).

NOTE:

NOTE: In order to change the vent lever position, you

NOTE:

will need to pull the lever out slightly to clear the

plastic tabs.

Step 10

For recessed bottom cabinet only

For r

If the cabinets have front, side or back trim, make 2

wood shims the width of the trim and attach them to

the cabinet bottom recess on both sides. See

1/8"

7/16"

previous page for marking locations.

5 1/4"

12 7/16"

13 15/16" (30" Hood)

16 15/16" (36" Hood)

Electrical access hole

(in wall)

Step 11

Cut holes at marked locations for duct and electrical

wiring. For the vertical duct, cut out 3/4" extra toward

the front of the cabinet so you can move the duct

freely when installing the hood.

It may also ease installation by cutting the hole 10 1/

2" instead of 10".

Step 12

Drive a mounting screw (from the hardware packet)

partway into each center of the narrow neck of the

Set for

keyhole slots marked on the cabinet bottom.

Step 13

Fix the wiring conduit to the hood.

Stop tab

Step 14

Slide the hood back against the wall. Tighten the

mounting screws. Be sure the screw heads are in the

narrow neck of the keyhole slot.

Connect Ductwork to hood.

TICAL

TICAL position (flat

TICAL

Installing the hood

ecessed bottom cabinet only

W W W W W ood shims

ood shims