Electrolux AIRSPEED ZAS1000A Manuel de l'utilisateur - Page 9
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Electrolux AIRSPEED ZAS1000A. Electrolux AIRSPEED ZAS1000A 12 pages. Airspeed technology
Également pour Electrolux AIRSPEED ZAS1000A : Manuel (12 pages)
Imprimer la page
How to Maintain Mini turbo nozzle
1) Turn nozzle onto back
side. Remove 1 screw.
Thermal Cut-Off
This vacuum has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum switches off,
turn the switch to off position and unplug the vacuum. Check the vacuum for a possible source of overheating such as a
full dustbin, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before
attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and push the on/off switch On ( I ).
If the vacuum still does not run, please call Electrolux Customer Care Helpline.
Service
Should you require service on your Electrolux vacuum,
please telephone Electrolux Customer Care HELPLINE
on 1300 365 305 (Aus) or 0508 730 730 (NZ). Before
requesting service, please check whether your problem
can be resolved in the Trouble shooting section on
page 10.
New filter pads, brush rolls and drive belts can be
obtained from Electrolux Retailers. If difficulty is
experienced in obtaining spares, please contact
Electrolux Customer Care HELPLINE.
Service Checklist
• If your vacuum will not operate, check the plug connection,
plug fuse and mains fuse.
• Never allow the dustbin to become so full that it impedes
the air flow, thus reducing the cleaning efficiency of the
machine. The character of household dust and its effect on
the air flow through the machine may vary considerably.
Fluffy dust allows air to pass through readily whereas fine
powdery dust or proprietary cleaning powders pack tightly
in the dustbin, offering greater resistance to air flow and will
reduce cleaning efficiency if the cup becomes overloaded.
• Always store your vacuum and spare dust filters in a
dry place.
• Renew the filter pads regularly. This is essential to ensure
continued high filtration of dust particles.
2) Rotate lower part of
cover down over brush
and lift off cover.
3) Clear blockage from
brush roll area. Use
scissors to clip
threads or hair.
• Sucking up such items as stockings, clippings of cloth,
sizeable pieces of paper, wrappings from cigarette packets
or sweets etc., may block the hose. Electrolux regrets that
the clearing of blocked hoses cannot be regarded as
service that can be given free of charge, under the
guarantee. Should a blockage occur, first disconnect the
vacuum from the electricity supply, refer to section headed
"How to Clear a Blockage." If these operations are not
successful, contact Electrolux Customer Care HELPLINE
1300 365 305 (Aus), 0508 730 730 (NZ).
• Never pick up hot cinders or lighted cigarette ends.
• Make certain that your vacuum does not come into
contact with water or any other liquid. It is not designed
as a wet pick up vacuum, and must never be used on
damp carpets or wet floors.
Important – in the event of the mains supply cable of this
vacuum requiring replacement, we recommend that this be
carried out by Electrolux Service Staff.
Spares
New filters, brush rolls and drive belts can be obtained from
Authorised Electrolux Dealers and electrical retailers. If
difficulty is experienced in obtaining spares please call
Electrolux Customer Care HELPLINE 1300 365 365 (Aus),
0508 730 730 (NZ). or visit our website at
www.electrolux.com.au
9
4) Place cover back
into position.
Tighten screw.