Bosch BDU3360 Mode d'emploi original - Page 44

Parcourez en ligne ou téléchargez le pdf Mode d'emploi original pour {nom_de_la_catégorie} Bosch BDU3360. Bosch BDU3360 45 pages. Drive unit
Également pour Bosch BDU3360 : Manuel du propriétaire (32 pages), Mode d'emploi original (47 pages), Mode d'emploi original (23 pages), Mode d'emploi original (32 pages)

Imprimer la page

English – 2

(8) Operation/battery charge indicator

(9) Battery on/off button

(10) PowerTube

(11) PowerPack

Technical data

Charger

Product code

Rated voltage

Frequency

Battery charging voltage

Charging current (max.)

Charging time for PowerTube 750, ap-

prox.

Charging time for PowerPack 400, ap-

prox.

Operating temperature

Storage temperature

Weight, approx.

Protection rating

A) You can find the charging times for additional batteries at:

http://www.bosch-ebike.com

The specifications apply to a rated voltage [U] of 230 V. These spe-

cifications may vary at different voltages and in country-specific mod-

els.

Operation

Start-up

Connecting the charger to the mains (see figure A)

Pay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the charger. Chargers marked 230 V can

also be operated at 220 V.

Plug the device connector (3) of the power cable into the

device socket (2) on the charger.

Connect the power cable (country-specific) to the mains.

Charging the removed battery (see figure B)

Switch the battery off and remove it from its holder on the

eBike. When doing so, read and observe the operating in-

structions of the battery.

Ensure the battery is placed on clean surfaces only.

Avoid getting dirt, e.g. sand or soil, in the charging socket

and contacts in particular.

0 275 007 3CX | (15.03.2022)

Plug the charging connector (5) of the charger into the

socket (6) on the battery.

Charging the battery on the bike (see figures C and D)

Switch the battery off. Clean the cover of the charging

socket (7). Avoid getting dirt, e.g. sand or soil, in the char-

ging socket and contacts in particular. Lift the cover of the

charging socket (7) and plug the charging connector (5) into

4A Charger

the charging socket (6).

BPC3400

There is a risk of fire due to the charger heating up

during charging. Ensure the battery on the bike is

220 ... 240

completely dry and placed on a fireproof surface be-

50 ... 60

fore charging. If this is not possible, remove the battery

from the holder and charge it in a more suitable location.

When doing so, read and observe the operating instruc-

tions of the battery.

Charging process

3.5

The charging process begins as soon as the charger is con-

nected to the battery or charging socket on the bike and to

the mains.

°C

0 to 40

Note: The charging process is only possible when the tem-

°C

10 to 40

perature of the eBike battery is within the permitted char-

0.7

ging temperature range.

IP40

Note: The drive unit is deactivated during the charging pro-

cess.

The battery can be charged with and without the on-board

computer. When charging without the on-board computer,

the charging procedure can be observed on the battery

charge indicator.

When the on-board computer is connected, a charging noti-

fication appears on the display.

The state of charge is displayed by the battery charge indic-

ator (8) on the battery and by the bars on the on-board com-

puter.

The LEDs on the battery charge indicator (8) flash during the

charging process. Each solid illuminated LED represents ap-

proximately 20 % of the charging capacity. The flashing LED

indicates the next 20 % currently charging.

Once the eBike battery is fully charged, the LEDs go out im-

mediately and the on-board computer is switched off. The

charging process is terminated. The state of charge can be

displayed for 5 seconds by pressing the on/off button (9) on

the eBike battery.

Disconnect the charger from the mains and the battery from

the charger.

When the battery is disconnected from the charger, the bat-

tery is automatically switched off.

Note: If you have charged the battery on the bike, carefully

close the charging socket (6) with the cover (7) after char-

ging, so that no dirt or water can get in.

If the charger is not disconnected from the battery after

charging, after a few hours the charger will switch itself back

on, check the state of charge of the battery and begin the

charging procedure again if necessary.

Bosch eBike Systems