Bose Panaray 502A Informations techniques - Page 4
Parcourez en ligne ou téléchargez le pdf Informations techniques pour {nom_de_la_catégorie} Bose Panaray 502A. Bose Panaray 502A 4 pages. Full-range-driver array loudspeakers
Également pour Bose Panaray 502A : Manuel d'installation (12 pages), Manuel (4 pages), Manuel d'installation (24 pages), Manuel d'installation (32 pages)
Imprimer la page
Panaray
502
System Accessories
®
®
A full line of accessories has been
specially designed by Bose for use
with the Panaray
502
system
®
®
components. These accessories
increase system configuration
flexibility and provide simple
solutions for typical installation
challenges.
502 A Controlled Array
Accessories
• CSB-5A Suspension Bracket
(2-point gravitational type, 0º - 45º
pitch range)
• WCB-5 U-bracket (for wall/ceiling
surface mounting, ±90º range)
• WBP-5 Bi-Pivot Bracket (single-
point surface mount, 0º - 45º pitch,
±80º yaw)
CVT-5 Constant
Voltage Transformer
Engineers' and Architects' Specifications
502 A Controlled Array
The mid- to high-frequency device
shall be a multiple-driver system with
matched active equalization as
follows:
The transducer complement shall
consist of five (5) high-sensitivity
drivers of 4.5 inches (11.4 cm) diam-
eter, mounted vertically on a single
baffle assembly such that directional
characteristics are optimized for
smooth response.
The input connector, located on the
rear of the array enclosure, shall
consist of a screw-type barrier strip.
The array enclosure shall be com-
posed of copolymer materials, with
outer dimensions of 23.5"H x 5.75"W
x 6.76"D (59.7 cm H x 14.6 cm W x
17.1 cm D); its weight shall be 15 lb
(6.8 kg).
The array maximum acoustic output
shall be 112dB-SPL from 130Hz to
15kHz, with measurements refer-
enced to full-bandwidth pink-noise
input at 1 meter at the array's rated
• CVT-5A Constant Voltage Trans-
former (70/100V distributed system
transformer and housing)
• PSA-5 Stand Adapter (compatible
with Bose SS5 and SS10 stands)
502 B Acoustimass
®
Enclosure Accessories
• CSB-5B Suspension Bracket
(2-point gravitational type, 0º – 30º
pitch range)
• 502 A EQ Card (not shown)
• Options for active equalization
WCB-5
U-bracket
power. Its power-handling capacity
shall be 150W continuous referenced
to IEC noise for 100 hours. The nominal
horizontal beamwidth shall be 120º.
The nominal vertical beamwidth shall
be 70º.
The loudspeaker shall be the Bose
Panaray 502A controlled array.
502 B Acoustimass
Enclosure
The low-frequency device shall be a
dual-ported highly compact enclosure
with matched active equalization as
follows:
The transducer complement shall
consist of one (1) high-power-handling
driver of 30 cm diameter, mounted
inside an enclosure such that distortion
is minimized as a result of acoustic
filtering. Its operating frequency range
shall be below 150Hz so that non-
localizability shall allow a high degree
of location placement flexibility.
The input connector, located on the
rear of the enclosure, shall be a screw-
Suspension
Suspension
WBP-5
Bi-pivot
Bracket
type barrier strip.
The enclosure shall be made of high-
strength, high-density resin-impreg-
nated vinyl-wrapped particle board,
with outer dimensions of 31.0"H x
14.0"W x 15.5"D (78.7 cm H x 35.6
cm W x 39.4 cm D); its weight shall
®
be 85 lb (38.6 kg).
The bass enclosure's maximum
acoustic output shall be 115dB-SPL
from 55Hz to 150Hz, with measure-
ments referenced to a full-bandwidth
pink-noise input at 1 meter at the
enclosure's rated power. Its power-
handling capacity shall be 450W
continuous referenced to IEC noise
for 100 hours.
The bass enclosure shall be the Bose
Panaray 502 B Acoustimass enclo-
sure.
©2006 Bose Corporation, The Mountain, Framingham, MA
01701-9168 USA
Subject to change without notice.
www.bose.com
269261 AM Rev.04 PC031391
CSB-5A
Bracket
CSB-5B
PSA-5
Stand
Brackets
Adapter