Absinthe 19006-01 Manuel rapide
Parcourez en ligne ou téléchargez le pdf Manuel rapide pour {nom_de_la_catégorie} Absinthe 19006-01. Absinthe 19006-01 2 pages. Universal series rf receiver
Imprimer la page19006-01
Universal series RF Receiver
Important: Read All Instructions Prior to Installation
Function introduction
DC Power input
V+
19006-01
V-
LED CONTROLLER
PRI:
Uin=12-36VDC
Learning
Switch
Iin=32.5A
SEC:
Uout=4x(12-36)VDC
Iout=4x8A
Pout=4x(96-288)W
TEMP RANGE:-20℃-+50℃
Master/Slave
Learning Key:
jumper
Paring with RF remote
Product Data
Input
Output
Output
Connector
Voltage
Current
Power
Current Rating
4x8A
12-36VDC
4x(96-288)W
Max. 20A
Radio Frequency : 869.5/916.5/434mhz
Waterproof grade: IP20
Safety & Warnings
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Pair/delete the pairing with RF remote
1.Do wiring according to connection diagram.
2.Pair RF Receiver with RF remote: please refer to the instruction of the remote that you would like to pair with.
3.Delete the pairing:
(1)Wire up the RF receiver correctly, power on.
(2)Press and hold down the " Learning Key" button on receiver for over 3 seconds until the connected light
flashes, which means well deleted.
Master and Slave Setting:
1. The receiver has both master and slave functions which can be set with a jumper. Short circuit of the jumper
means master function, and open circuit means slave function. Once short circuit the jumper on a receiver,
please power off and power on the receiver to enable master function. Setting master and slave enables perfect
synchronization of color changing effects.
2. Set one receiver as master and pair it to any zone of a remote, and this zone shall only have one receiver
which works as master. Set all other receivers as slave and pair them to other zones of the remote, and multiple
receivers can be paired to each zone. Then choose all zones on the remote and play the color changing
effects, the master will send sync signal to the slaves to achieve perfect synchronization. The max. sync
distance between the master and any slave is within 30m.
Common Anode Output(+)
V+
R-
CH 1:R/WW output(-)
CH1
G-
CH 2:G/CW output(-)
2
B-
B-
CH 3:B/WW output(-)
3
3
W-
CH 4:W/CW output(-)
4
Wire Size
Remarks
Size(LxWxH)
2
0.05-3.3mm
Constant voltage
170x59x29mm
(12-30AWG)
Wiring Diagram
1) When total load of each receiver is not over 20A
L
V+
12V/24V/36V
N
CV PSU
V-
G
V+
V+
19006-01
R-
V-
LED CONTROLLER
CH1
PRI:
Learning
Uin=12-36VDC
G-
Switch
Iin=32.5A
2
SEC:
Uout=4x(12-36)VDC
Iout=4x8A
B-
B-
Pout=4x(96-288)W
3
3
TEMP RANGE:-20℃-+50℃
W-
4
V+
V+
19006-01
R-
V-
LED CONTROLLER
CH1
PRI:
Learning
Uin=12-36VDC
G-
Switch
Iin=32.5A
2
SEC:
Uout=4x(12-36)VDC
Iout=4x8A
B-
B-
Pout=4x(96-288)W
3
3
TEMP RANGE:-20℃-+50℃
W-
4
V+
V+
19006-01
R-
V-
LED CONTROLLER
CH1
PRI:
Uin=12-36VDC
Learning
G-
Switch
Iin=32.5A
2
SEC:
Uout=4x(12-36)VDC
Iout=4x8A
B-
B-
3
3
Pout=4x(96-288)W
TEMP RANGE:-20℃-+50℃
W-
4
2) When total load of each receiver is over 20A
L
V+
12V/24V/36V
N
CV PSU
V-
G
V+ V-
V+
V+
19006-01
R-
V-
LED CONTROLLER
CH1
PRI:
Learning
Uin=12-36VDC
G-
Switch
Iin=32.5A
2
SEC:
Uout=4x(12-36)VDC
Iout=4x8A
B-
B-
Pout=4x(96-288)W
3
3
TEMP RANGE:-20℃-+50℃
W-
4
L
V+
12V/24V/36V
N
CV PSU
V-
G
V+ V-
V+
V+
19006-01
R-
V-
LED CONTROLLER
CH1
PRI:
Learning
Uin=12-36VDC
G-
Switch
Iin=32.5A
2
SEC:
Uout=4x(12-36)VDC
Iout=4x8A
B-
B-
Pout=4x(96-288)W
3
3
TEMP RANGE:-20℃-+50℃
W-
4
AC Power
50/60Hz
V+
V+
If Connect with RGBW LED Strip
R-
R-
G-
G-
B-
B-
W-
W-
V+
V+
If Connect with Single Color LED Strip
1-
V-
2-
V-
3-
V-
4-
V-
V+
V+
WW
WW
CW
CW
If Connect with Dual Color LED Strip
WW
WW
CW
CW
AC Power
50/60Hz
V+
V+
1-
V-
If connect with Single Color LED
2-
V-
3-
V-
4-
V-
AC Power
50/60Hz
V+
V+
WW
WW
CW
CW
If connect with Dual Color LED
WW
WW
CW
CW