DS Europe AN401Plus Manuel de démarrage rapide

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} DS Europe AN401Plus. DS Europe AN401Plus 2 pages.

Imprimer la page
Front panel
Slot C Transducer connections:
Terminal
Differential signal input card [I1 option]
Signal +
1
2
Signal -
3
Not connected
4
Not connected
5
Transducer's Power supply -
Transducer's Power supply +
6
1. Panel cut: 92 x 44 mm, depth: 110 mm (including rear terminal board).
2. Power supply: connect power supply to the instrument by means of the screw terminal
8 - 24 Vdc and 0 to 9 - 15 Vac, 1W power ).
Transducer connection: See Label on top of the instrument
3.
4. Calibration:
A. Power on the AN401Plus and push, at the same time, button ▼and C; when display shows FSET; release push buttons (by
releasing push buttons You enter into calibration menu). Wait at least 10-15min for warm up time.
B. Display shows LO: press
etc.).
No tare or pre-load is applied to the transducer (i.e.: 0 Kg = 0 default value ).
Refer to point E about how to set different ZERO value.
C. Verify that load cell is free from any load and then press
D. Display shows LO: press
E. Display shows HI: press
corresponding to a specimen applied onto the load cell or by using built-in calibration circuit: i.e. 500 Kg (1000 = default).
To increase or decrease the value press
It quickly.
F. Apply the specimen onto the load cell, or activate the built-in calibration circuit, and press
blinks MEMO.
G. Display shows HI: press
dp
H. Display shows
In example, to show 100,0 , set value to 2 (decimal point is set on second digit from right side) and press E.
Display shows dp: press
I.
3.820 kHz, 1 = 1.910 kHz, 2 = 960 Hz, 3 = 480 Hz, 4 = 240 Hz, 5 = 120 Hz, 6 = 60 Hz, 7 = 30 Hz, 8 = 15 Hz e 7 = 7.5 Hz.
Resolution depends on sampling rate: if high speed measures are not necessary, do not change default value.
J.
The AN401Plus is calibrated: press
shows the transducer's measure; default = MODO 1, NET value).
5. Dynamic zero: after calibration, the AN401Plus can show the transducer measures and, by pressing C, It will zeroes the displayed
measured value = DYNAMIC ZERO (this zeroing is not maintained after powering down the AN401Plus).
6. Grounding: if heavy electrical environmental noise is present the grounding pin (earth), on the rear panel of AN401Plus, is to be
connected to a good grounding well.
7. Alarm levels menu: by pressing
8. Complete manual: for a comprehensive list of AN401Plus functions make reference to the complete manual available under request
or from web site
www.dseurope.com
E
push button to store the ZERO numeric value (in the desired engineering units i.e. Kg, tons, daN
HI
▲
in order to show
E
and write the FULL SCALE numeric value (in the desired engineering units i.e. Kg, tons, daN etc.),
▲
or▼; to increase It quickly press
dp
▲
in order to show
E
(Decimal Point): press
to set the decimal point position.
adspd
▲
to show
(ad speed = analog/digital sampling rate). Default value is 8=15 Hz. Values are: 0 =
C
to exit from calibration and personalization menu (AN401Plus restarts Itself and display
▲
It is possible to set alarm levels values (see rear page).
.
AN401Plus
D
C
1
1
RJ-11A
2
2
CanBus
3
3
4
4
5
5
RJ-11B
RS-485
6
6
RS-232
5 4 3
2 1
9
8
7 6
EARTH
Single ended input card [I2 option]
Transducer' Power supply – (GND)
+ Input signal (0 to + 5 or 10V)
Not connected
Not connected
Not connected
Transducer's Power supply +
E (MEMO
blinks on display).
.
.
QUICK START MANUAL
B
A
1
1
Power supply connection
2
2
3
3
4
4
5
5
6
6
INPUT
Polarity free
5
4
3
2
1
, without bothering about polarity (0 to
and E, at the same time, or ▼and
▲
E
to memorize It: on display It
Rear panel
= AN401 Power supply
= AN401 Power supply
E
to decrease