DSC Envoy NT9010 Manuel de l'utilisateur - Page 11
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} DSC Envoy NT9010. DSC Envoy NT9010 20 pages. Demo stand
Également pour DSC Envoy NT9010 : Instructions d'installation (4 pages)
Imprimer la page
Section 9: Replacing Batteries
From time to time, the batteries in the detectors and other components on your
system will need to be changed. If a device has a low battery, your system will
announce a "Device Low Battery" trouble message (see Checking Trouble Con-
ditions on page 19).
When the batteries in one device need to be replaced, it is suggested that the bat-
teries in all system devices be replaced at the same time. The batteries used in the
devices are Eveready Alkaline Energizer or Energizer Lithium batteries.
NOTE: Before changing the batteries in the detectors, you should inform
your central station.
Tips for
• Your system is designed to work with either Eveready Alkaline Energizer or Lith-
Buying
ium batteries according to individual device. When replacing batteries, be sure
Batteries
to buy the same brand and type. Do not replace the batteries with any other
type. The reliability of your security system depends on its batteries, and "no
name" or generic brand batteries may not provide the best quality and
dependability.
• Use fresh batteries. Most batteries have a "best before" date printed on their
packaging or on the batteries themselves. Buy batteries that have a "best
before" date of two years or more from your purchase date.
• When disposing of used batteries, follow the instructions and precautions
printed on the batteries. Many cities and communities have collection sites or
disposal services. Contact your municipal offices for more information.
• If in doubt about the batteries used in your system, or if you have trouble
installing them, contact your installer for assistance.
Required Batteries
WLS904-433
Motion Detector
WLS904P-433
Pet Immune Motion Detector
WLS906-433
Wireless Smoke Detector
WLS929-433
Wireless Key
WLS912-433
Wireless Glassbreak Detector
WLS914-433
Pet Immune Motion Detector
WLS925L-433
Universal Transmitter
26
Four AAA batteries.
Four AAA batteries.
Six AA batteries.
Three Photo/Electronic 1.5V
batteries.
Three AA batteries.
Four AA batteries.
One Lithium Energizer No.
EL123AP battery.
Remote Telephone Access
NOTE: Please pause for 1 second between key presses when entering
access codes or commands on a remote phone.
1. From any touch-tone telephone, dial number of the line on which your NT9010
has been installed.
2. After one ring, hang up. Wait 10 seconds then call again. On the second call,
the system will answer after one or two rings and announce:
"Hello."
3. Enter your 3-digit Telephone Access Code within 10 seconds. If you wait longer
than 10 seconds, the system will automatically hang up.
4. The system will then prompt:
"Enter your access code."
Enter your [access code] within 20 seconds. If you wait longer than 20 seconds,
the system will hang up. The system will also hang up if 3 incorrect access
codes are entered.
5. Once you have entered an access code, the system will announce one or more
messages to advise you of its status. Follow the voice prompts to use the sys-
tem functions.
NOTE: There is only one "Telephone Access Code". It is programmed by
your installer. It is not the same as your 4- or 6-digit system access code.
More than one system access code can be programmed for use by different
users of your system (see Programming Access Codes on page 21).
Receiving
If you are accessing the NT9010 system over a local telephone at the same time as
someone calls you, the system will announce:
Incoming
Calls
"Attention, you have an incoming call. To receive the call, press pound now."
To answer the incoming call, press
use the system.
Recording and
You can record a voice memo on the NT9010 controller to be listened to at a later
time. To record a voice memo:
Playing Voice
Memos on the
1. Press the Record function button. The NT9010 says "Record memo now, To
NT9010
complete press [#]". The maximum memo length is 20 seconds.
2. Speak into the microphone (located in the top left corner of the unit). When
you have finished recording, press
a new memo has been recorded.
To listen to a voice memo:
1. Press the Playback function button. Once the memo has been played, the green
Ready light stops flashing, but the memo remains in memory until a new one is
recorded, or until the NT9010 loses all power.
Us in g Y o u r N T9 010 S ys t em
. If you do not press
, you can continue to
#
#
. The green Ready light flashes to indicate
#
7