DSC BV-400UL Instructions d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} DSC BV-400UL. DSC BV-400UL 2 pages. Quad motion detector, bravo 4 series

Imprimer la page

LOCATING THE DETECTOR

Select a detector location that will provide the coverage

required keeping in mind the following potential problems

Reflective Surfaces Do not aim the detector at reflective

surfaces such as mirrors or windows as this may distort the

coverage pattern or reflect sunlight directly onto the detector.

Air Flow Avoid locations that are subject to direct high air flow

such as near an air duct outlet.

Moisture Do not locate the detector near sources of steam or

oil.

Sun Do not aim the detector such that it will receive direct or

reflected (mirror) sunlight,

Pets If there are pets on the premises, use the pet alley lens.

Obstructions Do not limit the coverage by large objects

within the detection area such as plants or filing cabinets.

VERTICAL ADJUSTMENT

Using the Mounting Height Chart, set the vertical adjustment to

obtain the desired coverage. Ensure that the PCB retaining

screw is tightened just enough to prevent board movement.

JUMPER J1 will enable/disable the alarm LED. If J1 is OFF,

the LED will not operate on alarm. If J1 is ON the LED will

operate on alarm.

NOTE: The corridor lens should not be used in corridors that

are less then 5' in width and the installation should be carefully

checked to ensure that the beams are aimed directly down the

centre of the corridor.

WIRING

TAMPER

ALARM

POWER

CONTACT

CONTACTS

20 mA

100 mA

12 V

24 V

NOTE: This unit is UL Listed

and should be connected to a

listed control unit or power

TAMP 12V GND

NO NC C

LED

supply providing at least 4

hours of standby power.

10Ω

0.25W

Contacts shown with power applied

and no alarm

CHANGING LENSES

The Bravo4 is supplied with the "wall-to-wall" lens.

change the lens, release the top tab and pull the lens holder

out. This action releases the lens. Insert the lens with the

GROOVES FACING INWARD. The bottom of the lens is

indicated by two triangular indentations. Ensure that the lens

is centred left to right then reinstall the lens holder. The lens

holder will snap into place sealing the lens into position.

WALK TESTING

Once the detector has been set up, walk test the entire area

where coverage is desired. Should the coverage be incomplete,

re-adjust or relocate the detector to obtain full coverage. Once

coverage is as required, the alarm LED may be disabled by

setting J1 to OFF.

IMPORTANT NOTE: Upon installation, the unit should be

thoroughly tested to verify proper operation.

The detector should be walk tested weekly by the end user and

yearly by the installer.

DM-C and DM-W

Detector Mounting Brackets

Use the optional DM-W Wall Mount and DM-C Ceiling Mount

brackets to solve difficult placement problems. The DM-W and

DM-C mount to either the wall or ceiling and allow for full vertical

and horizontal positioning of the motion detector - the detector

can be tilted up or down and rotated through 90° to obtain the

best position for optimal coverage. The Bravo PIR has been

designed to be fully compatible with the DM-W and DM-C

brackets. Contact your DSC distributor for more information.

WIRING KNOCKOUTS

LOOSEN SCREW FOR

VERTICAL ADJUSTMENT

TAMP 12V GND

J1 ON = LED ON

J1 OFF = LED OFF

PIR SENSOR

TAMPER

SWITCH

CORNER MOUNT

KNOCKOUTS

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of 12 months from the date

of purchase, the product shall be free of defects in materials and workmanship under

normal use and that in fulfilment of any breach of such warranty, Digital Security

Controls Ltd. shall, at its option, repair or replace the defective equipment upon

return of the equipment to its repair depot. This warranty applies only to defects in

parts and workmanship and not to damage incurred in shipping or handling, or

damage due to causes beyond the control of Digital Security Controls Ltd. such as

lightning, excessive voltage, mechanical shock, water damage, or damage arising

out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original purchase, and is and shall

be in lieu of any and all other warranties, whether expressed or implied and of all

other obligations or liabilities on the part of Digital Security Controls Ltd. Digital

Security Controls Ltd. neither assumes, nor authorizes any other person purporting

to act on its behalf to modify or to change this warranty, nor to assume for it any other

warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or

consequential damages, loss of anticipated profits, loss of time or any other losses

incurred by the buyer in connection with the purchase, installation or operation or

failure of this product.

Motion detectors can only detect motion within the designated areas as shown in

their respective installation instructions. They cannot discriminate between in-

truders and intended occupants. Motion detectors do not provide volumetric area

protection. They have multiple beams of detection and motion can only be de-

tected in unobstructed areas covered by these beams. They cannot detect motion

which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass

doors or windows. Any type of tampering whether intentional or unintentional

such as masking, painting, or spraying of any material on the lenses, mirrors,

windows or any other part of the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in temperature. How-

ever their effectiveness can be reduced when the ambient temperature rises near or

above body temperature or if there are intentional or unintentional sources of heat

in or near the detection area. Some of these heat sources could be heaters, radia-

NO NC C

tors, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.

Warning: Digital Security Controls Ltd. recommends that the entire system be

LED

completely tested on a regular basis. However, despite frequent testing, and due

to, but not limited to, criminal tampering or electrical disruption, it is possible for

this product to fail to perform as expected.

Important Information: Changes or modifications not expressly approved by

Digital Security Controls Ltd. could void the user's authority to operate this

equipment.

VERTICAL

ADJUSTMENT

-1

SCALE

-2

WALL MOUNT

KNOCKOUTS

Toronto, Canada • • • • • www.dsc.com • 1-800-387-3630

Printed in Canada 29000112 R003

Direct all comments and suggestions concerning

DSC publications to [email protected]

[email protected]