DSC LC-100PI Instructions d'installation et utilisation - Page 2
Parcourez en ligne ou téléchargez le pdf Instructions d'installation et utilisation pour {nom_de_la_catégorie} DSC LC-100PI. DSC LC-100PI 2 pages. Pir motion detector with pet immunity up to 25kg
Imprimer la page
SETTING - UP THE DETECTOR
PULSE WIDTH JUMPER SETTING
3
Very stable environment
2
Position 1
1
Without PET
PULSE
LED ENABLE JUMPER SETTING
LED ON
PIR sensitivity adjustment
POTENTIOMETER "SENS"– adjustment according to protected area range.
Use the potentiometer to adjust the detection range between 68% and 100%
(factory set to 84%). Rotate the potentiometer clockwise to increase range,
counter-clockwise to decrease range.
Wire size requirements
Use #22 AWG (0.5 mm) or wires with a larger diameter. Use the following
table to determine required wire gauge (diameter) and length of wire between
the detector and the control panel.
Wire Length
m
200
Wire Diameter mm
.5
Wire Length
ft.
800 1200
Wire Gauge AWG
22
TESTING
Test procedures
Wait one minute - warm up time after applying 12 Vdc power.
Conduct testing with the protected area cleared of all people.
Walk test
1. Remove front cover. The pulse jumper must be in position 1. The LED must be e nabled. 2. Replace the front co ver.
3. Start walking slowly across the dete ction zone. 4. Observe that the detector's L ED li ghts whe never motion is detected.
5. Allow 5 sec. between each test for the detector to stabilize. 6. After the walk test is completed, the LED may be disabled.
Note: Walk tests sh ould be conducted, at l east once a yea r, to con fi rm p rope r operation and coverag e o f the detector.
TECHNICAL SPECIFICATION
Model
LC-100PI
Detection Method Quad (Four element) PIR
Power Input
8.2 to 16 VDC
Current Draw
Standby: 8mA (± 5%)Active: 10mA (± 5%)
Temp.
Compensation
YES
Alarm Period
2 sec (± 0.5sec)
Alarm Output
N.C 28VDC 0.1 A with 27Ohm series
protection resistor
LIMIT ED WARRAN TY: Digital Security Controls Ltd, w arrants that for a period of 12 m onths from the date of purchase, the product shall be free of defe cts in materials and workm anship unde r normal use a nd that in
fulfillment of any breach of such warranty. D igital Security Controls Ltd shall, at it s opt ion, repair or re place the defective equipment u pon ret urns of the e quipm ent to its repair d epot. This warranty applies only to de fects
in parts and workmanship and no t to damage incurred in shippin g or ha ndling, or damag e due to causes beyond the control of Digit al Security Con trols Ltd, such as lightning, excessive voltage me chan ical sho ck, wate r
damage, or damage arising out o f abuse, alteration or improper a pplication of the equipment.
The forego ing w arranty sh all apply only to the original buyer, and is and shall be in lieu of any and all o ther w arranties, whether expressed or implied and o f all othe r obligations o r lia bilities on th e part of Digital Security
Controls Ltd . Digital Security Controls Ltd neith er assumes responsib ility for, nor au thorizes an y oth er perso n purpo rting to act on its behalf to modify or t o cha nge this w arranty, nor to assume for it a ny ot her w arranty or
liability concerning this product.
In no event shall Digita l Security Con trols Ltd be lia ble f or any direct, indirect or conseq uential da mages, lo ss of anticip ated profits, loss o f time or an y oth er losses incurred by the buyer in conne ction with th e purchase,
in stallation or operation or failure of t his pro duct.
Motion det ecto rs can only detect mo tion within the de signated are as as Sh own in th eir re spe ctive inst allation instructions. Th ey can not discriminate betwe en intrud ers and inte nded occupants. Mot ion detectors do not
provide vo lumetric area prote ction. The y have multiple bea ms of d etection and mo tion can only be detected in unobstructed area s covered by these beams. They cannot detect motion which occurs beh ind w alls, ceilings,
flo or, closed doors, g lass partitions, g lass doors or windows. Any
type of tamperin g whe ther in tentional or unintentional such as m asking , painting, or spra ying of any ma terial on the lenses, mirrors, windows or any o ther part of th e detection system w ill impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. Howe ver their effectiven ess can be reduced when the ambient temperature rises ne ar or above body temperature or if there are intentional
or u nin ten tion al so urces of he at in or n ea r th e d et ectio n a rea. So me of t hese h eat so urces could be h ea ters, radia tors, sto ves, barb equ es, firep laces, su nligh t, stea m vent s, lig ht in g and so o n.
WARNI NG: Di gital Security Co ntrols Ltd , reco mm end s that th e en tire sys tem be com pletely tested o n a reg ula r basis. However, d espite fre qu ent testing , an d d ue to , bu t n ot lim ited to , crim inal tam perin g
or electrical d isru ption , it i s po ssible for this p rod uct to fail to p erfo rm as exp ecte d.
Im p ortan t in form a tio n : Ch an g es or mo d ifica ti on s no t ex pre ssl y ap p ro ved b y D ig ital Secu ri ty Co n tro ls L td c ou ld v oi d th e u se r's a uth or ity to op er ate thi s e qu ip m en t.
2005 Digital Security Controls Ltd
Toronto, Canada
www.dsc.com
3
Moderate nuisance situation
2
Position 2
1
PET up to 15Kg (33.1 Ib)
PULSE
LED OFF
300
400
800
.75
1.0
1.5
2000
3400
20
18
16
PET IMMUNITY JUMPER SETTING
25Kg
Immunity to an animal
PET
up to 15Kg (33.1 Ib)
15Kg
PCB LAYOUT
LED
JAMPER
TAMPER
PULSE
WIDTH
TAMPER
Tamper Switch
Warm Up Period
LED Indicator
RFI Protection
EMI Protection
Dimensions
Weight
3
Relatively high change of false alarms
2
Position 3
1
PET up to 25Kg (55 Ib)
PULSE
25Kg
Immunity to an animal
PET
up to 25Kg (55 Ib)
15Kg
PYROSENSOR
N.C 28VDC 0.1A with 10 Ohm series protection
resistor - open when cover is removed
60sec (± 5sec)
LED is ON during alarm
30V/m 10 - 1000MHz
50,000V of electrical interference from lightning
or power through
92mm x 62.5mm x 40mm(3.62'' x 2.46'' x 1.57'')
40gr (1.4oz)
BLOCK
CONNECTOR
SENSITIVITY
ADJUSTMENT
PET
IMMUNITY
ADJUSTMENT