DSC CLASSIC PC1555 Manuel d'instruction - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} DSC CLASSIC PC1555. DSC CLASSIC PC1555 11 pages.

Imprimer la page

8 ....... Loss of time on system clock. To set the system time, following the instructions in "Setting

System Date and Time" on page 13.

To view troubles from an LCD Keypad:

From the Ready state, use the arrow (< >) keys to scroll to the following message.

Press [ ] [2] to view the trouble. The message will read...

Select Option<>

System Test

Use the arrow (< >) keys to view which troubles are present on the system. Once you

System Test

have scrolled through the list of troubles, press the [#] key to exit the Trouble Viewing

In Progress

mode and return to the Ready state.

Setting the System Date and Time

To set the system time, enter [ ] [6] followed by the Master Code. Press [1]. The keypad will now

accept 10 consecutive digits:

• Enter the Time in Hours and Minutes using the 24 Hour format (00:00 to 23:59).

• Enter the Date in Months, Days and Years (MM DD YY).

NOTE: If you have an LCD keypad, your installer may have programmed your system to display the

time and date while the keypad is idle. If this is the case, you may have to press the [#] key to clear

the date and time before entering an access code to arm the system, or before performing any

other keypad function.

Testing Your System

Alarm Test

The Alarm Test provides a two second test of the keypad sounder and bell or siren. Begin with the

panel in the Ready state.

From an LED keypad, Enter [ ][6][Master Code][4] then press [#] to return to the Ready state.

From an LCD keypad, press [ ] to enter the functions list. Use the arrow (< >) keys to scroll to find "User

Functions" and press [ ] to select. Enter your Master Code and scroll to find the following message...

System Trouble

Press [ ] to perform an Alarm Test. The keypad will display the following message...

(*2) to View< >

View Trouble < >

Press [#] to return to the Ready state.

"Trouble Message"

Full System Test

We recommend that you test your system weekly. Should the system fail to function properly, call your

installation company immediately for service.

NOTE: Perform system tests at off-peak hours.

1. Inform the central station that you are testing your system.

2. Begin with the system in the Ready state.

3. Perform a Bell/Battery test by pressing [ ][6][Master Code][4]. The bell and keypad buzzer will

sound for two seconds and all keypad lights will turn ON. Press [#] to exit.

4. Activate each sensor in turn (e.g. open a door/window or walk in motion detector areas).

From an LED keypad, observe the zone light turn ON when the zone is activated. The zone light will

turn OFF when the system restores to normal (i.e. door or window closed).

From an LCD keypad, the following message will be displayed when each zone is activated...

Quick Arm

When the Quick Arm feature is enabled, the system may be armed by simply pressing [ ][0] instead of your

access code. Please note that pressing [ ][0] will only allow you to arm the system; to disarm, you must enter

a valid access code. Your installer will inform you if the Quick Arm feature has been enabled on your system.

Quick Exit

When the Quick Exit feature is enabled, pressing [ ][0] while the system is armed will provide a two minute

window for you to exit the premises. During this time, you may only open and close the designated Entry/

Exit door once. Once the door is closed, the panel will end the two minute quick exit delay. If the door is

opened again, or if the door is not closed after two minutes, or if another zone is opened, the panel will begin

the entry delay. Your installer will inform you if the Quick Exit feature has been enabled on your system.

Disarming the System

Disarming from an LED Keypad:

Enter the premises through a designated Exit/Entry door; entering by any other door will sound an

immediate alarm. As soon as the Exit/Entry door is opened, the keypad will beep to indicate that the

system should be disarmed. Go to the keypad and enter your access code. If an error is made

entering the code, enter your code again. As soon as the correct code is entered, the Armed light

will go out and the keypad will stop beeping.

The correct access code must be entered before the entry delay period expires. If a valid access

code is not entered during this time, the system will go into alarm. The entry delay time may be

changed by your installer.

If an alarm occurred while the system was armed, upon disarming the system, the Memory light and

the zone light corresponding to the zone which caused the alarm will flash for 30 seconds. After the 30

second period, the Memory light and zone light will stop flashing and the panel will return to the Ready

state. Pressing the [#] key during the 30 second period will cancel the alarm memory display. To view

other alarms, press [ ][3].

If a trouble was detected when the panel is disarmed, the Trouble light will turn ON (See "Viewing

Trouble Conditions" on page 12 to determine the source of the trouble.) Please note that troubles will

not display while the system is in the Alarm Memory Display mode.

Disarming from an LCD Keypad:

Upon entering through a designated Exit/Entry door, the keypad will beep and the entry delay will

commence, reminding you to disarm the system. The keypad will display the following message...

Enter your access code. If an er

Entry Active

Enter Your Code

again.

again. When a valid access code is entered, the keypad will stop beeping. If no

again.

alarms occurred while the panel was armed, and there are no troubles, the display

System Disarmed

will read...

No Alarm Memory

After about five seconds, the system will return to the Ready state and the display

Enter Code to

will read...

Arm System

If an alarm occurred while the system was armed, this message will be displayed.

View Memory < >

Use the arrow (< >) keys to view which zones caused the alarm. If a zone is still in

"Zone of Alarm"

alarm, the display will show the following message to indicate that a zone is open...

Secure System

Before Arming <>

Upon disarming and if a trouble is present, this message will be displayed. Use the

arrow (< >) keys to view which troubles are affecting the system (see "Viewing

Enter Code to

Trouble Conditions" on page 12).

Arm System

< >

If an err r r r r or is made in entering the code, enter the code

If an er

or is made in entering the code, enter the code