Auber Instruments AT210 Manuel d'instruction - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Auber Instruments AT210. Auber Instruments AT210 4 pages. Digital
Également pour Auber Instruments AT210 : Notes sur l'utilisation (2 pages), Manuel d'instruction (3 pages), Manuel d'instruction (3 pages)

Imprimer la page

AUBER INSTRUMENTS

AT210-B. When the peak value is cleared from the AT210-B, this

operation will also be synchronized to the AT210-A, and the peak value

will be cleared.

2) Muting the alarms. When you press the SHIFT key to mute the

alarm buzzer, it will only be effective to the buzzer on this unit. The

buzzer on the other unit will continue sound until temperature left the

alarm zone, or the SHIFT key on that unit is pressed.

3) Placing distance. Placing the AT210-A and the AT210-B too far or

too close will result in bad signal reception on the AT210-B. Signal

reception can be affect by distance, physical obstacles, and other

factors. The AT210-B and the AT210-A can be placed 100 feet away

from each other in an open space.

Figure 6. Velcro mounting (left) and stainless steel plate mounting (right).

11. Placing and Mounting the Meter.

The meter should be placed in a working environment where

temperature is -20-50° C (0-100° F). It should be placed away from high

heat to protect the plastic housing and electronics. Two mounting options

are provided: 1) A pair of Velcro fastener. The Velcro has a pressure

sensitive adhesive backing. You can remove the protective film from the

hook piece and stick it to the back of the meter (see Figure 6). Then

remove the protective film from the loop piece and install it onto the wall.

Please note that the pressure sensitive adhesive on Velcro is industrial

grade with strong holding force. It needs to be stick on a solid surface.

Don't put it on a drywall because it may peel off the paint if you decided

to remove it later. 2) A stainless steel mounting plate. The plate allows

the meter to be hung on a hook or a nail. It also allows the meter to be

permanently mounted with a screw. The bottom part of the stainless

steel mounting plate is covered with pressure sensitive adhesive. To

install it onto the meter, peel off the pink colored releasing film; press it

firmly onto the back of the meter (see figure 6).

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

2020.09

the user is encouraged to try to correct the interference by one or more

of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly

approved by manufacturer could void your authority to operate this

equipment.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Auber Instruments Inc.

5755 North Point Parkway, Suite 99,

Alpharetta, GA 30022

www.auberins.com

E-mail: [email protected] Tel: 770-569-8420

No part of this datasheet shall be copied, reproduced, or transmitted in any

way without the prior, written consent of Auber Instruments. Auber Instruments

retains the exclusive rights to all information included in this document.

WWW.AUBERINS.COM

P4/4