Conairphone FX944 Manuel du propriétaire - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Conairphone FX944. Conairphone FX944 11 pages. Call waiting/caller id sport telephone with digital answering system

Imprimer la page

INSTALLATION

Choose Your Location

Your unit must be placed on a hard flat surface and connected

to both the telephone wall jack and an AC power source. Allow

at least one inch to the rear and four inches above the unit for

ventilation.

Connect to AC adaptor

Use only the provided FX944 AC Adaptor

1. Plug AC adaptor cord into the back of your unit.

2. Plug AC adaptor into a standard 120 volt wall outlet. Do not

attach (staple, etc.) the AC adaptor cord to the building wall.

3. Once the AC adaptor is plugged into the outlet, you will hear

a series of beeps.

To Install One 9 Volt Battery

In the event of a power failure, one 9 volt alkaline battery (not

included) is required to maintain your personalized outgoing

announcement and recorded messages. If the battery is not

installed, your personalized outgoing announcement and

recorded messages will be lost.

To install battery

1. Open the battery door by pulling back the

latch.

2. Install one 9 volt alkaline battery.

3. Snap the battery door back into place.

To replace battery

Replace battery once a year to ensure proper operation of the

power failure protection feature.

1. Unplug the FX944's telephone line cord from the wall outlet.

NOTE: DO NOT unplug the AC adaptor from the wall or from

the FX944, or the outgoing announcement and incoming

messages will be lost.

2. Follow Steps 1 to 3 in "To install battery" section.

3. Plug the telephone line cord back into the wall outlet.

Your message counter will show "bL" until battery is

installed. Your unit is functional without the battery. The

battery is only necessary for power failure protection.

SETTING UP YOUR FX944

DO NOT CONNECT the line cord to the wall outlet until the

Caller ID setup has been completed.

The LCD shows 'ENTER LANGUAGE'

followed by a choice of 3 languages

(English, Spanish, French). If your

display does not appear this way, press

and hold both [ ] and [ ] for 4 seconds.

The LCD then shows 'ENG ESP FRA'.

NOTE: The 'ENG' is blinking. Press [ ]

or [ ] to select 'ENG', 'ESP', or 'FRA'.

Press [DELETE] to confirm.

Once ENG is selected, the LCD shows

'LCD CONTRAST'.

Press [ ] or [ ] to adjust five levels (from

1 to 5, default is 3) contrast of LCD.

Press [DELETE] to confirm.

Once contrast is set, the LCD shows

'ENTER AREA CODE'. The first digit

'–' of the area code will blink.

Press [ ] or [ ] to enter the area code.

Press [DELETE] to confirm and go to next entry.

Repeat above steps until 3-digit area code is set.

The LCD shows 'TOTAL:00 NEW:00',

which means both the total call and new

call counter are zero.

Connect the Telephone Line

1. Plug your telephone line into the modular telephone jack at

the bottom of your unit.

NOTE: Do not plug a cordless telephone into your unit.

Operation of a digital answering system may cause

interference with your cordless telephone.

2. Plug the telephone line cord into the modular phone line jack

and the modular outlet in your telephone wall jack.

With a four prong style jack, simply use a plug in modular

adapter.

3. Your system is ready to answer incoming calls with a

prerecorded-outgoing message, "Please leave your message

after the beep". To record a personalized outgoing message,

refer to page 10.

USING THE PHONE ON A DESK

1. Plug the long telephone line cord into the jack in the bottom

of the base, thread it through the groove toward the back of

the unit, then plug it into the modular phone jack.

2. Connect the coil cord to the jack in the handset and the base.

HANGING THE PHONE ON THE WALL

When the FX944 is wall mounted, the handset guide holds the

handset in place in the cradle.

On a wall phone plate

1. Plug the short telephone line cord into the jack in the base

bottom and into the jack on the plate.

2. Hang the base onto the two pins and pull the base down to

lock it on.

3. Plug the coil cord into the handset and base jacks.

On a wall without a plate

1. Install 2 screws with anchors into the wall, one above the

other, 3-1/4" apart, extending 3/16" out from the wall to hold

the base securely.

2. Install the long telephone line cord into the jack in the base,

thread it through the groove and plug it into modular wall jack

as shown.

3. Hang the base on the screws and pull it down to lock it on.

4. Plug the coil cord into the handset and base jacks.