Anywire BL296 B-16F Series Manuel du produit

Parcourez en ligne ou téléchargez le pdf Manuel du produit pour {nom_de_la_catégorie} Anywire BL296 B-16F Series. Anywire BL296 B-16F Series 11 pages.
Également pour Anywire BL296 B-16F Series : Manuel du produit (17 pages)

Imprimer la page

AnyWireASLINK System Products Guide

ASLINKTERMINAL

BL296□B-16F□-4A-20

The Products Guide describes individual products. Refer to the Guide as necessary.

■Function List

Model

ASLINKTERMINAL

NPN 16-point input/16-point output

four-wire

PNP 16-point input/16-point output

(isolated) cable

NPN 8-point input/8-point output (hybrid)

type

PNP 8-point input/8-point output (hybrid)

■Notes on use

To set any address, an "Address writer ARW-04 (Ver. 04-1.01 or higher), ARW-03 (Ver. 2.10 or higher)"

⇒

is required. Please prepare it separately.

[Notes on Safety]

Precautions that must be observed in order to use this system safely are indicated as shown below.

You must observe these precautions.

A WARNING indicates a potentially hazardous

situation which, if not handled correctly, could

result in death or serious injury.

WARNING

○ System Safety

This system is intended for general industrial applications. It does not have functions for supporting applications requiring higher

levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes.

WARNING

○ Always turn off the power before attempting to mount or replace.

○ Prolonged continuous ow of a rated load current or higher or a transit current due to load short-circuit, etc., in the hybrid unit including

the output unit and the output circuit may result in smoking or ring. An external safety device such as a fuse must be installed.

○ System power supply

Use a stable, 24V DC power supply. Use of an unstable power supply may cause problems with the system.

○ Separately route high-voltage and power cables

CAUTION

Although the AnyWireASLINK has a high noise margin, keep the transmission line and I/O cables away from high-voltage and

power cables.

○ Connectors and terminals

* Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected.

* Make sure to prevent any metal objects from getting inside the connectors or the terminal blocks.

* Short-circuits caused by metal objects or mis-wiring are likely to damage the device.

○ Do not impose any external loads on the units. Doing so may cause a failure.

○ Do not disconnect or reconnect between the transmission line and slave units. A malfunction may occur.

○ Use the AnyWireASLINK within the range of the speci cations and conditions shown below.

[Warranty]

■ Warranty period

The warranty on the delivered Product shall continue to be effective for one (1) year after the delivery thereof to a location as

designated by the original owner.

■ Scope of warranty

Should a defect occur in any part of the Product during the foregoing warranty period when it is used normally in acordance with

the speci cations described in this User's Manual, the Company shall replace or repair the defect free of charge, except when it

arises as a result of:

[1] Misuse or abuse of the Product by the owner;

[2] Fault caused by other than the delivered Product;

[3] The unauthorized modi cation or repair of the Product by any person other than the Company's personnel;

[4] Any unusual force of nature, disaster or other cause beyond the Company's control.

The term "warranty," as used herein, refers to the warranty applicable to the delivered product alone. The Company shall not be

liable for consequential or incidental damages resulting from any malfunction.

■ Repair at cost

After the expiration of the warranty period, the owner shall be responsible for all costs and expenses incurred for the trouble-

shooting and repair of the Product. Even during the warranty term, the Company shall repair any defects arising from causes

other than within the scope of the warranty as speci ed above, at the owner's cost.

[Type]

BL296SB-16F-4A-20

BL296PB-16F-4A-20

BL296XB-16F-4A-20

[ASLINK Small Integrated 16-Point Terminal]

Speci cations

NPN input

NPN output

NPN input/NPN output

-BL296*B16F*4A20 1/11-

Connection targets

Universal sensors

Slave unit

voltage

and switches,

reduction

universal output

devices

○

A CAUTION indicates a potentially hazardous situation

which, if not handled correctly, may result in personal

injury or property damage.

CAUTION

BL296SB-16FS-4A-20

PNP input

BL296PB-16FS-4A-20

PNP output

BL296XB-16FS-4A-20

PNP input/PNP output

Functions

Sensing

I/O

level

short

disconnection

circuit

reduction

I/O

Small-

power supply

sized

reduction

○