Anzzi FR-AZ174 Manuel d'installation - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Anzzi FR-AZ174. Anzzi FR-AZ174 2 pages.
Imprimer la pageＨａｎｄｌｅ ｉｎｓｔａｌｌａｔｉｏｎ
Disassemble the cold water handle
(identified by a blue dot).
Leave the bottom retainer ring as well as the
rubber and metal washers in place. From
under the bathtub insert the cold water valve
(indentified by a C) in the hole located on the
right of the spout hole.
Using the nut, adjust the height of the valve
so the bottom of the flattened part of the
threads is aligned with the top of the bathtub.
From the top, install the remaining rubber
and metal washers. Screw the nut to secure
the valve, handle flange and handle in place.
Repeat steps to install the handle and hot
water valve (identified by an H) in the hole
located on the left of the spout hole.
Ｓｐｏｕｔ ｉｎｓｔａｌｌａｔｉｏｎ
Unscrew the Allen screw from behind
the spout. Pull apart the spout from its
connector (do not unscrew)
Unscrew the superior spout nut of the
spout connector. Make sure that the nut
and the metal and rubber washers are
in place on the spout connector. From
underneath the bathtub, insert the top
of the connector in the hole between
the two handles. From over the bathtub,
screw the superior spout nut to secure
the connector in place.
Place o-ring underneath the spout flange
and reinstall the spout on the anti-turn
pin, making sure to insert the stop rod in
the stop hole. Tighten spout in place by
screwing the Allen screw behind
the spout.
Ｈａｎｄ ｓｈｏｗｅｒ ｈｏｌｄｅｒ ｉｎｓｔａｌｌａｔｉｏｎ
Unscrew the bottom nut and take off
metal and rubber washers.
Insert the hand shower holder in the
hole making sure to place the o-ring
underneath the fix holder. From under,
screw the rubber and metal washers,
as well as the retainer ring to the holder
in place.
Connect the hose to the hand shower,
making sure that the rubber washer is
in place. From above, slide the hose
through the holder to sit the hand
shower on its base.
Ｓｔｅｐ １
1
2
3
4
A
Ｓｔｅｐ ２
1
2
B
3
Ｓｔｅｐ ３
1
2
3
Ｓｔｅｐ ４
Ｖａｌｖｅ ａｎｄ ｗａｔｅｒ ｓｕｐｐｌｙ ｃｏｎｎｅｃｔｉｏｎ
1
Using the flexible connectors included,
connect the valves to the spout
connector. Use the extra flexible
connector to join the spout to the hand
shower hose. Tighten using appropriate
tool (ill. A).
2
Connect hot and cold valves to the
corresponding water supply lines using
flexible connectors (not included) and
tighten (ill.B).
Ｓｔｅｐ ５
Ｔｅｓｔｉｎｇ ｃｏｎｎｅｃｔｉｏｎｓ
ＷＡＲＮＩＮＧ： Ｒｅｍｏｖｅ ａｅｒａｔｏｒ ｂｅｆｏｒｅ
ｔｅｓｔｉｎｇ ｃｏｎｎｅｃｔｉｏｎｓ． Ｄｏ ｎｏｔ ｏｖｅｒｔｉｇｈｔｅｎ．
1
Verify that there are no leaks by slowly
opening the hot and cold water. In case
of a leak, shut off the water supply and
tighten connectors 1⁄4 turn using the
appropriate tool. Repeat if necessary.
2
Turn on the faucet and leave both hot
and cold water running for at least one
minute to evacuate the air trapped in
the pipes. Turn off water.
3
Assemble the aerator as illustrated and
insert into the spout, tightening by hand.
You can now turn on water supply.