Casio 2496 Manuel de l'utilisateur - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Casio 2496. Casio 2496 7 pages.

Imprimer la page

• Note the following important points whenever performing a data

communication operation.

Make sure the two IR ports are pointed directly at each other.

Make sure the two IR ports are within 10cm (3.5 inches) of each other.

Keep the watches still until they beep, which indicates the end of data

communication.

To help ensure the watches remain still, do not try to look at their displays

until they beep.

Align the IR ports of the two watches within 10 seconds after performing

the button operations to set up the sender and receiver.

• In the case of user information, the two watches exchange their information

with each other. See "Exchanging User Information" for more information.

• Data Bank data can be sent one record at a time, while Mail data can be

sent one message at a time. See "Communicating with Another Watch" for

more information.

• If you experience problems with data communication, see

"Troubleshooting".

Exchanging User Information

In the case of user information, the two watches exchange their information

with each other, just like two people exchanging names, e-mail addresses,

and phone numbers. Received user information is ultimately stored in the

Data Bank Mode.

• The user information that your watch sends to another watch is the data

you have input in the User Information Mode. Before sending user

information, use the User Information Mode to check it to make sure it is

correct.

To exchange user information

1. Decide with the owner of the other watch who will be the sender and who

will be the receiver.

• It makes no real difference which watch sends user information first. The

following operation causes both the sender and the receiver to get the

information of the other watch.

2. On both watches, press C to enter the Timekeeping Mode.

• What you do next depends on whether you are the sender or receiver.

The sender should perform steps 6 through 8, while the receiver should

perform steps 3 through 5.

3. On the receiver watch, hold down B for about

two seconds.

4. When the watch beeps, release B. This

causes the

on the display.

5. Point the face of the receiver towards the

sender, and perform steps 6 through 8 on the

sender.

6. On the sender watch, hold down E for about

two seconds.

7. When the watch beeps, release E. This

causes the

display.

8. Point the face of the sender at the face of the

receiver, so they are face-to-face.

• User information data exchange starts at

this time.

• Data exchange can take up to 11 seconds. During that time, keep the IR

ports pointed at each other and avoid moving the watches.

9. Both watches beep to indicate when data exchange is complete.

• After data exchange is complete, the watches beep and the message

appears on the displays of both watches for about five seconds.

OK!

Next, the watches enter the Data Bank Mode, each showing the data they

just received.

• If data exchange was not successful for some reason, the watches beep

and display the message

ERROR!

happens, perform the above procedure again from step 1.

Communicating with Another Watch

Use the following procedures to exchange Data Bank Mode data and Mail

Mode messages with another watch. In this configuration, one watch is the

sender and the other watch is the receiver.

• When a watch receives a mail message, the message text is stored in page

Px4 of the Mail Mode.

To receive data from another watch (receiver operation)

1. Press C to enter the Timekeeping Mode.

2. Hold down B for about two seconds.

3. When the watch beeps, release B. This

causes the

on the display.

4. Point the face of the receiver towards the

sender, and have your partner perform the

sender operation.

• Data communication starts at this time.

USER'S GUIDE 2496

REC

(receive) indicator to appear

indicator to appear on the

SEND

for about five seconds. If this

(receive) indicator to appear

REC

• Data exchange can take up to six seconds. During that time, keep the IR

ports pointed at each other and avoid moving the watches.

5. Both watches beep to indicate when data communication is complete.

• After data communication is complete, the message

receiver display for about five seconds. Next, the watch displays the data

that it received.

• If data communication is not successful for some reason, the watches beep

and display the message

ERROR!

receiver enters the Timekeeping Mode. If this happens, perform the above

procedure again from step 2.

To send data to another watch (sender operation)

1. Enter the mode (Data Bank Mode or Mail

Mode) that contains the data you want to

send, and display the data.

2. Hold down E for about two seconds.

3. When the watch beeps, release E. This

causes the

display.

• At this point, your communication partner

(the receiver) should also be setting up to

receive.

4. Point the sender's IR port at the receiver's IR

port, so the watches are face-to-face. Data

communication should start automatically.

• Data communication can take up to six

seconds to complete. Keep the watches still

until they both beep.

• After data communication is complete, the message

sender display for about five seconds. Next, the watch displays the data that

it sent.

• If data communication is not successful for some reason, the watches beep

and the message

appears for about five seconds. After that the

ERROR!

sender display shows the data you selected to send in step 1, above. If this

happens, perform the above procedure again from step 2.

Troubleshooting

Problem

Probable Cause

• You did not release

Even though I

hold down E to

the button.

• A setting screen

send or B to

receive, the

(digits or cursor

applicable

flashing) is on the

display.

SEND

• The watch is not in

indicator

REC

does not appear

the correct mode.

• Battery power is low.

on the watch's

display.

• Both watches are

The

set up as senders

ERROR!

message keeps

(

on the

SEND

appearing when

display) or receivers

I try to perform

(

REC

on the

data

display).

• The two IR ports are

communication.

too far from each

other.

• The two IR ports are

not pointing straight

at each other.

• After

SEND

appeared on

REC

the display of the

watch you took

longer than about 10

seconds to align the

two IR ports.

• The watches were

moved during data

communication.

OK!

appears on the

for about five seconds. After that the

SEND

indicator to appear on the

OK!

appears on the

What you should do

• After the watch beeps, release

the button.

• Press A to exit the setting screen.

• Enter the Timekeeping Mode to

exchange user information data

with another watch.

• To send Data Bank data or a mail

message, enter the applicable

mode and then perform the send

operation.

• To receive Data Bank data or a

mail message, enter the

Timekeeping Mode.

• See "Battery".

• Make sure

is on the

SEND

display of the sender, and

REC

is on the display of the receiver.

• Make sure the two IR ports are

no more than 10cm (3.5 inches)

from each other. Communication

becomes more stable the closer

the IR ports are to each other.

• Make the two IR ports are

pointed straight at each other.

• Align the IR ports of the two

watches within 10 seconds after

SEND

appears on one watch

and

appears on the other

REC

watch.

• Keep the IR ports of the two

watches pointed straight at each

other until the watches beep.

• Remove the watches from your

wrists and place them on a table

or other surface to keep them still

during data communication.

• See the illustration for information

about how the watches should be

oriented during data

communication. Be sure to

perform each step in order, from

1 to 4.