Casio 2296-1 Manuel de démarrage rapide - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Casio 2296-1. Casio 2296-1 6 pages.

Imprimer la page

Example

2 × 12 = 24

5 × 12 = 60

9 = 5

9 = 8

17 + 17 + 17 + 17 = 68

(2.3)

= 27.9841

To perform the above (2.3

To correct input errors and clear the calculator

The following table describes how to correct input errors and how to clear the

calculator after you finish using it.

When you need to do this:

Correct or change the value you are

currently inputting, without deleting the

rest of the calculation you have input

Correct or change the arithmetic operator

(+, –, ×,

) you have just input

Clear the calculation you are inputting

Clear a displayed calculation result

(produced by pressing the

key) and its

calculation

WORLD TIME

The World Time Mode shows the current time in 27 cities

Mode indicator

(29 time zones) around the world.

• For full information on city codes, see "CITY CODE

Current Time

TABLE" at the back of this manual.

• All of the operations in this section can be performed in

the World Time Mode, which you can enter by pressing

To view the time in another city

In the World Time Mode, press

Displayed city

City code

through the city codes and

standard time

To toggle a World Time city between DST and standard time

1. In the World Time Mode, display the city code whose

DST/Standard Time setting you want to change.

• You can make separate settings for each city code.

2. Hold down C for about two seconds to toggle between

DST (DST displayed) and standard time (DST not

displayed).

• The DST indicator appears on the display to indicate

that daylight saving time is turned on.

DST indicator

• Note that the DST/Standard Time setting affects only

the currently displayed city code. Other city codes are

not affected.

Note

• The DST setting of the World Time Mode and Timekeeping Mode are linked. This

means that using the World Time Mode to change the DST setting of the city that

you have selected as your current time zone in the Timekeeping Mode also changes

the setting of your current time zone.

• If you have a North American time zone (LAX, DEN, CHI, NYC) selected in the

Timekeeping Mode and DST AUTO turned on for the DST setting, changing the

DST setting in the World Time Mode for your time zone also turns DST AUTO off

and changes the time zone to the DST setting (DST ON or DST OFF) you select. If

you wish to continue automatic switching between DST and Standard Time, you

must change the DST setting back to DST AUTO.

You can set a Daily Alarm that sounds at the same time

Hourly time signal

each day, while it is turned on. You can also turn on an

on indicator

Hourly Time Signal that causes the watch to beep twice

every hour on the hour.

• Alarm settings (and Hourly Time Signal settings) are

available in the Alarm Mode, which you can enter using

Important!

Hour : Minutes

Setting an alarm time in period from midnight to 0:15AM,

Alarm on indicator

2:00AM to 2:15AM, or 4:00AM to 4:15AM causes the

automatic calibration signal receive operation during that

period to be skipped.

Operation

)

Perform this key operation:

Press C to clear the displayed value

and return to the 0 display. Next,

input the value you want.

Without pressing C, press the key

for the correct arithmetic operator.

Press C to clear the displayed value

and return to the 0 display. Next,

press C again.

Press C.

to scroll forward

to scroll back.

ALARM

To set the alarm time

Display

1. In the Alarm Mode, hold down A until the left hour digit of the alarm time starts to

24.

flash, which indicates the setting screen.

60.

• This operation automatically turns on the Daily Alarm.

2. Use the keypad to input the alarm time.

• The flashing selection automatically advances to the right each time you input a

number. You can also use C and D to move the flashing digit between the left

68.

hour, right hour, left minute's, and right minute's settings.

27.9841

• If you are using the 12-hour timekeeping format, press

AM and PM.

• When setting the alarm time using the 12-hour format, take care to set the time

27.9841

correctly as a.m. (A indicator) or p.m. (P indicator).

3. Press A to exit the setting screen.

Daily Alarm Operation

The alarm sounds at the preset time each day for about 10 seconds, or until you stop

it by pressing any button.

To test the alarm

In the Alarm Mode, hold down C to sound the alarm.

To turn the daily alarm and hourly time signal on and off

In the Alarm Mode, press C to cycle through the on and off settings as shown below.

Alarm Off

Signal Off

Hours

To measure times with the stopwatch

Elapsed Time

Start

Split Time

Start

Two Finishes

Start

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

To turn the input tone on and off

1. Enter the Calculator Mode.

2. Hold down A for about two seconds to toggle the input tone on and off.

• The input tone on/off setting you make in the Calculator Mode is applied to all

other modes, except the Stopwatch Mode.

Auto Return Features

• After you perform an operation in any mode, pressing B returns to the Timekeeping

Mode.

• If you leave a screen with flashing a digit or a cursor on the display for two or three

minutes without performing any operation, the watch automatically saves anything

you have input up to that point and exits the setting screen.

• If you leave the watch in the Telememo or Alarm Mode for about two minutes without

performing any operation, it automatically changes to the Timekeeping Mode. The

watch also reverts to the Timekeeping Mode if you leave it in the Calculator Mode

for about six or seven minutes without performing any operation.

Daily Alarm Only

Hourly Time

Signal Only

STOPWATCH

The stopwatch lets you measure elapsed time, split times,

and two finishes.

1/100 second

• The display range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• All of the operations in this section are performed in the

Seconds

Stopwatch Mode, which you can enter by pressing B.

Minutes

➤

Stop

Re-start

➤

Split

Split release

➤

Split

Stop

First runner

Second runner

finishes.

Display time of

first runner.

REFERENCE

2296-4

to toggle between

Alarm On

Signal On

➤

Stop

Clear

➤

Clear

Stop

➤

Split release

Clear

Display time of

second runner.