Danner 02710 Instructions d'entretien et d'utilisation

Parcourez en ligne ou téléchargez le pdf Instructions d'entretien et d'utilisation pour {nom_de_la_catégorie} Danner 02710. Danner 02710 2 pages.

Imprimer la page

CARE AND OPERATING INSTRUCTIONS FOR PONDMASTER

9.5, 12 & 18 PUMPS

ITEM # 02710, 02712, 02718, 02720, 02722 & 02728

FEATURES

The pump is a magnetically driven centrifugal water pump. It has no seals to wear and contains no oil. The

pump can be used submerged or inline. Inline means connections are made directly to the pump inlet and

outlet ports, which have

" NPT threads. All electrical components are encapsulated in epoxy. The energy used

is approximately 1/2 of regular driven pumps. The prefilter is provided for use in situations where debris in the

water could clog or damage the pump. This helps to give uninterrupted service.

INLINE PIPING

Centrifugal pumps cannot pull water from a lower level. In order to start, pump must be below water level

and filled with water. Unless the air can escape from the outlet, the pump will not start. Do not use glues or

solvents to connect the pumps threaded fittings. Use Teflon pipe tape. The pump cover is not designed to

support long pipe runs or to correct pipe misalignment.

SERVICE AND MAINTENANCE

The pump cover should occasionally be removed to clean and inspect the impeller assembly. The impeller is

the only serviceable item and can be pulled out of the body . Do not take the impeller apart. If it is worn or

broken the entire impeller assembly should be replaced. This will restore the pump to original capacity. Pumps

taken out of service for an extended period with fluid inside run the risk of forming a crust which may prevent

subsequent starting. Saltwater should be flushed out with fresh water. Always check cord for sharp bends

which can cause premature cracking. Do not use power cord to lift or move pump. Other than Impeller

maintenance, this appliance has no user serviceable parts.

IMPORTANT: FOR PUMPS USED IN SALTWATER OR HARD WATER

Magnet impeller assembly must be routinely removed for cleaning in white vinegar to remove accumulations

of scale or calcium. This procedure should be done at least once every three months - or more often if the

water conditions require it. Disassemble magnet from impeller by pulling them apart (it may take a strong pull).

One end cap will come off. To clean the calcium scale off the shaft and bearing inside of the magnet, soak in

white vinegar for a few hours and scrape it off. Reassemble magnet / impeller assembly. Do not lose any

washers located between the end cap and impeller.

CAUTION

The pump is intended to pump water only. It cannot be used to pump oil, solvents, or gasoline. Although the

pump will continue to run if there is no water, after 30 minutes damage may occur if allowed to run dry.

ELECTRICAL PRECAUTIONS

WARNING

- Risk of electric shock - This pump is supplied with a grounding conductor and grounding-type

attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly

grounded, grounding-type receptacle. Always use a properly grounded outlet. Do not immerse plug in water.

DO NOT REACH INTO WATER TO REMOVE PLUG. TURN OFF CIRCUIT FIRST. A "drip loop" should be provided. The

"drip loop" is a loop in the cord below the level of the receptacle or plug that prevents water from traveling

along the cord. The National Electric Code requires that a ground fault circuit interrupter (GFCI) be installed

in the branch circuit supplying fountain or pond equipment. Your dealer can supply GFCI units. NEVER

REMOVE GROUND PIN FROM PLUG. WARNING: FOR YOUR PROTECTION ALWAYS UNPLUG THE UNIT FROM ITS

POWER SOURCE BEFORE INSTALLING OR SERVICING. SHOULD THE UNIT APPEAR TO BE NOT WORKING DO

NOT REACH, REMOVE OR DISASSEMBLE BEFORE YOU DISCONNECT POWER.

L IM I T E D W A R R A N T Y

Danner pumps are warranted against failure due to defects in materials and/or workmanship as follows: Pump body, cover

and filter and accessories within five years of original purchase. Impeller and internal moving parts within one year of original

purchase. This warranty does not cover any replaceable filtering material supplied with the pump or filter as it is considered

expendable. This warranty covers defects occurring under normal use. The warranty and remedies set forth herein are condi-

tional upon proper installation, use, maintenance, storage, and conformance with the applicable use. It will be based upon

Danner Mfg. discretion as to whether the defects are of manufacturing origin. For warranty repair, return only the part that is

defective to our factory. Please include a dated proof of purchase and $5.00 for postage and handling. Any damages due

to improper installation are not covered by this warranty. This warranty does not apply to appearance or accessory items. This

warranty does not include damage due to handling, transportation, unpacking, setup, installation, repair or replacement of

parts supplied by any other than Danner Mfg.; improper maintenance, modification or repairs by the purchaser; abuse,

misuse, neglect, accident, fire, flood, or other acts of God. Any oral statements about this product made by the seller, the

manufacturer, their representatives or any other parties do not constitute warranties and shall not be relied upon by the user

and are not part of this contract. Neither the seller nor the manufacturer shall be liable for any injury, loss or damages, direct,

incidental, or consequential, including but not limited to incidental or consequential damage for lost profits, lost sales, injury,

and inability to use the product and the user agrees that no other remedy is available. Before using, the user shall determine

the suitability of the product for their intended use and the user shall assume all risk liability whatsoever in connection there-

with. To validate this warranty, keep your proof of purchase (copy of sales receipt from a certified Pondmaster or Supreme

dealer). Warranty covers the repair or prorated replacement of the Danner Mfg. products. Danner Mfg. denies all liability for

any other loss including but not limited to loss of equipment, income, livestock, vegetation or personal injury.

THE FOLLOWING VOIDS WARRANTY: LINE CORD OR PLUG IS ALTERED OR CUT, PRODUCT LABELS ARE DEFACED OR REMOVED.

PRODUCT IS IMPROPERLY INSTALLED OR MAINTAINED BY USER OR THEIR AGENT. PRODUCT IS ABUSED, MISUSED, OR DAMAGED

BY USER OR THEIR AGENT. PRODUCT IS NOT REMOVED FROM SERVICE AND DRIED DURING FREEZING CONDITIONS.