Danner PONDMASTER CLEARGUARD 15810 Instructions

Parcourez en ligne ou téléchargez le pdf Instructions pour {nom_de_la_catégorie} Danner PONDMASTER CLEARGUARD 15810. Danner PONDMASTER CLEARGUARD 15810 2 pages. Uv clarifier kit

Imprimer la page

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Electrical Precaution; To reduce the risk of electrical shock, connect only to a properly grounded, grounding type

receptacle. The National Electric Code (NEC), Article 680-41(A) requires ground fault circuit interrupter (GFCI) be installed in the

branch circuit supplying fountain equipment. Only a 3-wire grounding extension cord and grounded outlets should be used. If

the extension cord plug can reach the water and be accidentally submerged it should be secured to prevent submersion.

WARNING: Read All Instructions

1. Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location

portable luminaire. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety.

2. Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW, SEOOW, SOW, SOOW,

STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.

This portable luminaire / ballast assembly has an IP65 rating making it suitable for damp and wet locations when assembled in accordance

with these instructions. Do not submerge ballast.

CONSIGNES DE SÉCURITÉ IMPORTANTES

Utilisez uniquement des rallonges extérieures à trois ls munies de ches à trois broches et d'une prise de terre acceptant la che de

l'appareil. Si le problème persiste, contactez un électricien quali é. Ne jamais utiliser avec une rallonge à moins que la che puisse être

complètement insérée. Ne modi ez pas la che.

AVERTISSEMENT: lisez toutes les instructions

1. Une protection par disjoncteur de fuite à la terre (GFCI) doit être fournie sur le (s) circuit (s) ou la (s) prise (s) à utiliser pour

luminaire portable pour site humide. Les prises sont disponibles avec une protection GFCI intégrée et peuvent être utilisées pour

cette mesure de sécurité.

2. Utilisez uniquement avec une rallonge pour utilisation à l'extérieur, telle qu'une rallonge de type SEW, SEOW, SEOOW, SOW, SOW,

STOW, STOW, STOW, STOOW, SJEW, SJEOOW, SJW, SJOW, SJOOW, SJTOW, SJTOW, ou SJTOOW.

3. Cet ensemble portable de luminaire / ballast a un indice de protection IP65 le rendant approprié pour les endroits humides et

mouillés une fois assemblé conformément aux instructions jointes. Ne pas submerger le ballast.

UV CLARIFIER OPERATING INSTRUCTIONS:

replace an existing UV Clari er or add a second unit to Clearguard Pressure lters.

It can only be used in conjunction with the Clearguard lters indicated above.

INSTALLATION INSTRUCTIONS:

ALWAYS DISCONNECT PUMP BEFORE INSTALLATION.

1) Before installing the UV Clari er assembly into the lter cover, the lamp must

be installed. Carefully unpack the ballast / quartz sleeve assembly and remove the

quartz sleeve by rmly holding the black collar section and turning it count-

er-clockwise until it disengages from the lamp socket assembly.

2) Unpack the lamp and insert the contact pins on the lamp base completely into

the lamp socket.

For the 9 Watt unit: Continue to step 3.

For the 18 Watt unit: Find the lamp retainer in the lamp box and slide it onto

the lamp until it is snug in the socket. Next insert the alignment disk onto the

end of the lamp to keep it centered inside the quartz sleeve.

3) Make certain that the at gasket and O-rings are properly installed. See FIGURE 1.

Flat gasket sits on top of the of the quartz sleeve and O-ring ts outside the tube,

under the top ange. See FIGURE 1

4) Lubricate the Gasket and O-rings with Silicone grease for easier assembly.

Never use petroleum based lubricants.

5) Insert the UV lamp assembly into the Quartz sleeve and hand tighten - turning

clockwise until secure.

6) Insert the lamp / quartz sleeve assembly into either of the UV port openings in

the pressure lter cover.

7) Secure it by rotating the threaded ring of the UV xture clockwise onto the

lter cover's threads until tight.

8) After COMPLETE installation, UV Clari er can be brie y tested; plug the power cord into a grounded GFCI protected outlet to check.

The UV light can be safely viewed through the clear plastic cap on the xture. After testing, disconnect power until the lter is running.

The UV unit should only be powered on when the pressure lter is fully assembled with water circulating.

UV CLARIFIER KIT

MODEL ITEM # Fits Clearguard lter

9 Watt 15810

18 Watt 15820

This UV kit can be used to

Model 2700

Models 5500, 8000 & 16000

UV FIXTURE

WITH BALLAST

THREADED

RING

LAMP SOCKET

WITH SAFETY

SWITCH

UV LAMP

LAMP

RETAINER

ALIGNMENT

DISK

FLAT GASKET

O-RING

UNDER TOP

FLANGE

QUARTZ

SLEEVE

NOTE: YOUR FILTER AND

UV ACCESSORIES

MAY VARY FROM

REFERENCE ILLUSTRATION.

DO NOT OPERATE UV

CLARIFIER UNTIL READING

ALL OPERATING

INSTRUCTIONS, NOTES AND

PRECAUTIONS.

FIGURE 1

NOTE POSITION OF FLAT

GASKET AND O-RING.

FLAT GASKET

SEATS ON TOP

OF QUARTZ

SLEEVE

POSITION

O-RING

OUTSIDE THE

TUBE, BELOW

THE FLANGE

EXTRA UV

PORT CAP

(removed)

OPEN UV PORT

ON FILTER COVER