Audioplex MONOGIZER 200 Manuel d'installation

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Audioplex MONOGIZER 200. Audioplex MONOGIZER 200 2 pages. W/ optimatch converts stereo signals to mono

Imprimer la page

MONOGIZER 200 & MONOGIZER 300 w/ OPTIMATCH

Attenuator Type:

Connector:

Power Rating:

Frequency Response:

Transformers:

Attenuation:

OPTIMATCH(tm):

Mounting:

Your MONOGIZER(tm) is designed to convert Stereo signals to Mono eliminating the need for dual-cone speakers.

This unit is not for use on bridged amplifiers.

Follow the wiring diagram on the next page for installation of your MONOGIZER . Prepare the wire leads to and from the

MONOGIZER(tm) by stripping about 1/4" of insulation from each of the ends. Twist strands tightly together so that none stick out to

cause a possible short. Observe Polarity!

If you are using the impedance matching feature of the OPTIMATCH(tm) control, set the index following the chart below. To

set, remove the knob and loosen the nut to reposition the index. Make sure that the index is not between detent positions and tighten.

Install the control in its operating location. The MONOGIZER will fit in most double gang junction boxes. (SUGGESTION:

Leave control 3 or 4 positions CCW from maximum before firing up the system for the first time to avoid "blasting" the speakers,

while still having enough sound to observe operation.

If amplifier balance is adjusted left or right of center, the audio level will go down. The balance control should be kept to

center if possible. CAUTION! Under no circumstances should this unit be fed with a single channel positive. Both left and right

positives must be utilized. The Monogizer should not be attached to your system without a load to it's output, i.e. A speaker or the

equivalent wattage dummy load resistor.

IMPEDANCE MULTIPLES

X32

(STEP 7)

X64

(STEP 6)

X128

(STEP 5)

Do Not Remove

X256

Optimatch

(STEP 4)

X512

(STEP 3)

X1024

(STEP 2)

OFF

(STEP 1)

2002 - 3/15/02

INSTALLATION MANUAL

TECHNOLOGY

Converts Stereo Signals to Mono.

SPECIFICATIONS

Tapped auto transformer.

Screw-tight type.

72 Watts RMS continuous, 35 Hz-20 KHz, 216 Watts Audio.

100 Watts RMS continuous, 35 Hz-20 KHz, 300 Watts Audio.

+0, -1 dB worst case(-6 dB tap), +0, -0.2 dB all other taps, 35 Hz-

20 KHz, measured at full power, 8 Ohm load. Most controls better

these specifications.

Tri-filar wound for flat response and minimum phase shift, grain

orientated high silicon steel laminations.

-34 dB in 12 steps, 8 steps @ -3 dB each, 1 step @ 4 dB, 1 step @

-6 dB, last step OFF.

Will match impedance for almost any situation. Mechanical index

permits presetting load impedance multiplication by X4, X8, X16,

X32, X64, etc., which can be changed at any time.

72 Watt version Fits into most standard single gang electrical boxs.

100 Watt version requires a double gang box.

INSTALLATION

X16

(STEP 8)

(STEP 9)

DEFAULT

FACTORY

(STEP 10)

SETTING

We do not recommend wiring more than 8 Optimatch(tm) controls in parallel (NOTE: Do not

run more than (2)-8 Ohm speakers per channel). In these instances more impedance protection

should be inserted before the volume controls. The OC-12 is a good choice in this case.

#4 Ohm

#8 Ohm

Load

Speakers

(Ohms)

Per Channel

4.0000

2.6667

2.0000

1.6000

1.3333

1.1429

1.0000

0.8889

0.8000

0.7273

0.6667

No. of Available

Tap Setting

Steps for

For Matchit(tm)

Optimatch(tm) Controls

X16