Consort CRXSL-01 Manuel d'installation et d'utilisation - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} Consort CRXSL-01. Consort CRXSL-01 6 pages. Single zone wireless controller
Imprimer la page
12. Set programme inactive
To deactivate a programme, enter the programming mode.
Select the programme you want to make inactive and
touch
. The time and temperature will now be dashes to
indicate that the programme has been deactivated. In order
to re-activate the temperature setting, touch
13. Copy day function
The CRXSL allows you to copy a day's heating programme to
save time re-entering the same time and temperature settings
for a day.
1. To use a copy day function, enter the programming
mode.
2. To skip time setting, touch
day.
3. On the next tap, the Programme mode is activated and
the day will flash.
4. Touch
to activate the COPY DAY function.
5. Touch
to select the day you want to copy the
temperature settings from.
6. Touch
or
to select the day you want to copy the
temperature settings to.
7. Touch
to confirm the selection.
The 'to' word will flash to indicate that the day programme
has been copied to the day selected.
Touch
to go back to the Programme mode.
8.
14. Fan function - only available for fan heaters
Touch any control icon to activate the CRXSL touch
activate or deactivate the fan function.
15. Advance mode
Touch
from SETB or PROG mode to bring forward next
programme. To clear advance mode, touch
16. Keys locking
Touch and hold
together for 5 seconds. The display will
show
symbol. Repeat the step to unlock.
17. Heat symbol on the display
Every time there is a demand for heat, the display will show
the heat icon.
- Reduced heat output when the room temperature is
close to the set temperature ('RX' products
- Full heat output.
18. Status light on the heater
Light colour
Heater status
Heater is in stand-by mode/ not
receiving signal from CRXSL.
OR
Reduced heat output (RX only)
Full power heat output
Heater is ready for pairing with
CRXSL see section 3 "Pairing" for
OR
details.
FAULT - Overheating (RX only)
I3984093 Iss 01
again.
to cycle through hour and
to
.
only).....
Power options, installation guide and setup menu
The CRXSL is a wireless thermostat giving high precision room
temperature control. It is also a 7 day programmer with up to
6 temperature settings per day. Each CRXSL can control any
number of heaters in the same room (zone).
The CRXSL controller is compatible with the MRX1 Multizone
controller. Please refer to the instructions of the MRX1 when
connecting the CRXSL controller to the MRX1.
19. Choosing a position in a room
The CRXSL should be fixed to the wall or used with the table
top bracket. Avoid areas with draught or direct sun. Do not
position CRXSL above or close to the heaters or other heat
sources. Damp areas or areas where CRXSL can be
mechanically damaged should also be avoided.
20. Power options
The CRXSL controller can be powered either by a 5V power
adapter with a micro USB connector, supplied power
adapter via USB port or 4 AAA batteries. There are 2
available USB ports for power. One port is located on the
bottom and one at the back of the controller.
21. Batteries
Remove the CRXSL's battery cover and insert 4 new high
quality alkaline AAA batteries.
Warning: Consort is not responsible for damage due to
corrosion. Battery leakage will cause permanent damage.
Do not use batteries when unit is powered on with mains.
To help avoid battery leak:
Replace the batteries annually, even if there is not a
low battery warning. Remove failing or flat batteries
immediately.
Always fit a pair of new high quality alkaline batteries
from the same pack. Never mix new and old batteries,
or batteries of different brands or types.
Never attempt to revive alkaline batteries by heating,
crushing or recharging.
Note: The clock has to be set after replacing the batteries, or
if the USB power cable has been removed from the CRXSL.
This does not apply if it is being used with the MRX1 Multizone
controller.
4