Consort SLPBWIFI Manuel d'installation et de contrôle - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et de contrôle pour {nom_de_la_catégorie} Consort SLPBWIFI. Consort SLPBWIFI 8 pages. Wireless controller

Imprimer la page

6. Manual mode

The temperature control feature will effectively main-

tain the set room temperature. The target tempera-

ture can be set using the Consort Connect app. The

range is 4ºC - 35ºC. Once the room temperature

reaches the set temperature, the indicators will

change from green to red for 4 seconds before

switching off completely. When the room tempera-

ture drops, heating will became active and the indi-

cators will change to green.

7. Frost protection

Frost protection mode works the same way as man-

ual mode, maintaining a target temperature from

4ºC - 15ºC. These two modes can be used together,

by selecting manual mode at a higher temperature

when heat is required and then selecting frost pro-

tection at a lower temperature when no heat is re-

quired.

8. Boost mode

Boost mode can be used to provide a boost of heat

for a short period of time. When the button on the

controller is pressed, boost mode is triggered for 15

minutes. Once the boost timer has expired, the con-

troller will return to its previous operating mode.

9. Automatic mode

The Consort Connect app has a 7 day automatic

timer. This can be set to switch the heater on/off au-

tomatically at certain times of day. Each day has 24

heating periods, each period must be set to a re-

quired temperature.

The timer has an automatic 'preheat period' which

turns the heater on from 5-30 minutes before the au-

tomatic program begins. This time period can be set

in the basic settings menu.

Information on how to set the automatic program

can be found in the 'Setting the automatic timer'

section.

10. Energy Consumption

Selecting the

icon will load the Energy con-

sumption screen how much power heaters connect-

ed to SLPBWIFI used in the previous 24 hour period, 7

day period, 4 week period and the last year.

The energy usage values are approximate. They are

based on recording time the heaters are producing

heat. The mains voltage and actual heater wattage

aren't taking to account when calculating values.

11. Temperature Calibration

The temperature reading has been factory cali-

brated but if for any reason it needs adjusting

(better accuracy required, to suit different posi-

tion in the room etc.) the reading can be recali-

brated in 0.5 degrees steps via the Consort Con-

nect App. The calibration can be done +/- 2ºC

of the original value.

12. Basic settings menu

To access the basic settings menu, select the

settings icon from the main control page. In the

settings menu, select the title 'basic' to access

the basic menu. In this menu, you can view the

wattage of the heater, adjust the temperature

calibration and toggle open window detection,

the occupancy sensor and self learning mode

on/off. An SL pairing signal can also be sent

from this menu. More information on this can be

found in the section titled 'Pairing your SL heat-

er'. There is also an option to disable all indica-

tor lights on the controller. After pressing the but-

ton the controller will briefly show the status by

enabling the light indicators for period of 4 sec-

onds. The light indicators will be automatically

enabled after activating WIFI pairing.

13. Naming the product in the Consort Connect app

Once the controller is linked with the app, it is given

a generic name and the icon associated with it is a

heater. These can both be changed.

To do this, when the controller menu is open (this is

the menu you can control the product with) select

the

icon in the top right corner of the screen.

Next, select the

icon again. From this page, you

can change the name of the controller and import

an image to represent your product.

14. Open Window Detection

Ensuring you don't waste energy on heating the

outside world, the controller is equipped with

optional open / closed window detection. The

controller recognises sudden drops in temperature

when a window or a door is opened and turns the

heating off to save energy. When the window is

closed, the heater will automatically detect a

temperature rise, and switch itself back on. Once

enabled in the Consort Connect settings menu, the

open window detection is fully automatic and does

not require any human intervention to be activated.

Setting-up Open Window Detection

The system has been factory set to default time and

temperature values. If necessary, all values can be

adjusted. When the heating is on, open window

detection sensor will automatically switch the heater

off when it detects a fall in temperature of 2°C in less

than 10 minutes. If a temperature rise of 2°C in less

than 5 minutes is detected, the heater will switch

itself back on. These parameters can be changed in

the Consort Connect App. When viewing the heater

settings in the app, select the 'open window

detection' menu.