APL DIAGRAM X2 Instructions d'installation

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} APL DIAGRAM X2. APL DIAGRAM X2 2 pages.

Imprimer la page

Electrcal Connections: Timer model. (Diagram X2.)

Remove the internal cover by removing the 2 small caps and retaining philips

screws to access the terminal connections. The fan can either be operated

from a separate pullcord switch fitted to the ceiling of the room or can be

connected to the light switch so that the fan will start when the light is switched

on. A double pole fused spur having a contact separation of at least 3mm in all

poles must be used and fitted with a 3 amp fuse, and should be sited outside

any room containing a shower or fixed bath. The fan should not be accessible

to a person using either the shower or the bath.

Timer Adjustment

The Timer fan will run approximately one minute after it has been switched off.

This time delay can be increased by firstly switching off the power to the fan.

Remove the cover and the timer cover as detailed in diagram X2A. Insert a small

screwdriver into the slot, marked

reduce the time and anti-clockwise to increase the time. Only adjust with power

switched off. the timer will run for is 20 seconds and the maximum is about 20

minutes. NB Timer delay is adjustable as indicated on the timer strip cover.

Electrical Connections: Electronic Humidity Model (Diagram 3)

For the fan to operate as a normal time delay unit with humidity over-ride i.e.

when connected with a switched live coming from the light switch into the fan,

the fan will operate when the light is switched on, and switch off after about 20

seconds to 20 minutes (timer is pre-set for the minimum). However should the

humidity in the room reach about 75%, which will happen if the shower is run or

the bath filled with hot water, the fan will switch on and keep running until the

humidity has been reduced to a normal level, about 65%. Connect to electrical

supply as shown in diagram 3.

100mm Tile Fan, T. Max 40˚C Rated 220-240V ~50Hz 20W

150mm Tile Fan, T. Max 40˚C Rated 220-240V ~50Hz 25W

IMPORTANT

Switch off mains supply before making any electrical connections.

Installation must be supervised by a qualified electrician.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the applicance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other

open-fire appliances when mounted in outside windows or walls.

Fan must be disconnected from electrical power before any maintenance is carried out.

in Diagram X2A, and turn clockwise to

IP24

DIAGRAM X1

STANDARD MODEL

DIAGRAM X1A

TERMINAL

SIDE VIEW

BLOCK

TRIM

CABLE

When screw is tightened fixing

clip fingers secure the fan

Fan

Fixing clip

chassis

Ceiling board

Screw

HUMIDITY OPERATED TIME DELAY CONTROL

MAX

MIN

45min

1 min

The timer and humidity adjustments are as the normal instructions

TOP VIEW

COVER

POWER

CABLE

MOTOR WIRE

6mm

9mm

SECURE

CORD GRIP

POWER SUPPLY

SCREW FIXING HOLES

NEUTRAL

LIVE

3 AMP

REMOTE PULLCORD

DOUBLE POLE

SWITCH / LIGHT SWITCH

FUSED SPUR

OFF

RH%

Diagram 3

90%

40%

Time Delay & humidity

over-ride

operation

Terminal 1 - 1 Neutral Supply

Terminal 2 - 2 Switch live Supply

Terminal 3 - 3 Spare

Terminal 4 - 4 Permanet supply

FIXING

CLIP

HOLES

POWER

CABLE

ENTRY