4-noks IntellyGreenPV ZR-TIDCI.D-PV-EM Instructions d'assemblage - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions d'assemblage pour {nom_de_la_catégorie} 4-noks IntellyGreenPV ZR-TIDCI.D-PV-EM. 4-noks IntellyGreenPV ZR-TIDCI.D-PV-EM 2 pages.

Imprimer la page

WIRING THE DEVICE

Connecting counting input to a clean contact output (S0 output)

Connect S0 output to

terminal (5) and (6)

Connecting alarm input to a clean contact output (S0 output)

Connect S0 output to

terminal (8) and (9)

Waring:

If an optical interface is not used, make sure the counting

input (and alarm input) is connected to outputs with voltage

free contact.

Do not apply differences of potential to these terminals

contacts.

Otherwise, the device may be damaged beyond repair.

OPERATING CONTROLS

Button

If pressed for longer than 10 seconds the device is reset to its original

state (disconnected device).

This action causes the loss of data relating to the radio communication

and the loss of connection with the In-house Display and all devices

connected to it.

LIGHT SIGNALS

Led State

Description

Continuous light orange.

Indicates that the device is not

Short flash every 20

connected to any radio network.

seconds.

Flashing indicates that the

Flashing Green

device is operating normally.

4-noks s.r.l. - Francenigo di Gaiarine (TV) Italy

ASSOCIATION TO THE IN-HOUSE DISPLAY

Normally the device is supplied in the kit along with the In-house Display and

normally the two objects are already connected and therefore able to work

immediately after their powering, without additional configuration.

If for some reason there's no association between the two devices (because

of the disconnection of the In-house Display or Radio Transmitter) you can

connect them again.

Association of the device:

Turn on In-house Display and Radio Transmitter

Verify that the Radio Transmitter is not connected to any radio

network (the LEDs are all switched on and perform a quick flash

for two seconds every 20 seconds), otherwise disassociate the

device by pressing the button for more than 10 seconds.

Acting on the In-house Display, open the radio network

(Menu/Radio Management/ Open Radio Network) following the

steps:

Press the button under "Menu"

Select "Open Radio Network"

A few seconds after opening the network, the device should connect to the

radio network of the remote display. The operation's success is highlighted

by the flashing of led LD1 of the device.

If after 30 seconds from the opening of the network the device is still not

connected, maybe the chosen location is not suitable; in this case place the

device closer to the In-house Display or install another Repeater (ZR-

REPE230M).

When finished, close the radio network via In-house Display.

STANDARDS

Regulations: 2006/95/CE, 89/336/CE, 99/5/CE

Standards:

EN 300 328, EN 301 489, EN 61000-6-2, EN 6100-6-3,

EN 60950-1

Disposal

In case of disposal, the products must be disposed of separately in

accordance with applicable local laws.

Warranty Conditions

The warranty period is 2 years from the date of installation or 30 months

from the date of manufacture.

The warranty applies only in UK.

The manufacturer agrees to replace or repair the components that are

found defective.

Damage caused by improper installation, by a power supply not

compliant with the CEI EN 50160 standard, by the incorrect use or

failure to comply with the instructions contained in the Assembling

Installation is not covered by the warranty.

NOTES:

Select "Open Radio Network"

Confirm this request to open

the In-house Display radio

network

At the end of the association

process, confirm this request to

close the In-House Display

Radio Network

INSTRUCTIONS

INPV

SERIES

001

VERSION

1.4

DATE

06 / 2011