APlusLift MT1500X Manuel d'installation et instructions d'utilisation - Page 15
Parcourez en ligne ou téléchargez le pdf Manuel d'installation et instructions d'utilisation pour {nom_de_la_catégorie} APlusLift MT1500X. APlusLift MT1500X 20 pages. Motorcycle lift
Ope ra t ing I nst ruc t ions
5 .
5.1 Check T he Safety Lock Assembly:
Never operate the lift if the safety lock assembly is not working.
1.
WARNING!
2.
ALWAYS RELEASE THE MANUAL SAFETY LOCK LATCH BAR ONCE AIR PRESSURE IS
APPLIED THROUGH THE FOOT PEDAL TO THE CYLINDER AND THE LIFT STARTS TO
RAISE.
3. Raise the lift all the way with no load on the lift.
4. With the lift fully raised, ensure the safety latch bar is down so it will engage on the locks. With the locking bar
in position, always lower the lift until the safety bar rests on a lock and supports the lift.
5. T H I S T EST SH OU LD BE DON E ON A DAI LY BASI S T O EN SU RE THAT THE SAFET Y BAR I S
WORK I N G CORRECT LY !
5.2 To Position, Lift, And Low er Equipment On T he Lift:
1. Before pushing equipment onto the lift make sure that the lift is fully lowered, and the approach ramps are
attached and resting on the floor. Also, for two wheeled equipment, ensure that the front wheel vise is opened
up enough to fit the equipment's front wheel. Loads must be centered on the table at all times. The center of
the table is rated for a maximum load of 1,500 lbs.
2. Push the equipment over the lift while keeping the equipment parallel with the lift and aligning the center of
gravity of the equipment with the center of the lift. For motorcycles and other two wheel vehicles/equipment,
push forward until the front wheel goes between the clamps on the front wheel vise.
EQU I PM EN T ON T O OR OFF OF T H E LI FT ! PERSON AL I N J U RY M AY OCCU R WH I LE
ST EPPI N G DOWN FROM T H E EQU I PM EN T, AN D CAN ALSO CAU SE SERI OU S DAM AGE
T O T H E LI FT ! PU SH EQU I PM EN T ON T O T H E LI FT WI T H OU T PASSEN GERS! AGAI N ,
N EV ER DRI V E EQU I PM EN T ON T O Y OU R LI FT !
3. Engage the parking brake of the equipment if applicable.
4. Once the equipment is parked and the ignition is turned off, secure the equipment to the lift by tightening
the front wheel vise
to create a snug grip on the w heel. Do NOT overtighten the clamp as this can possibly
damage your w heel.)
5. Before lifting:
Alw ays tie dow n the equipment using straps through the tie dow n eyelets
mounted on the lift's table surface. DO T H I S EV ERY T I M E BEFORE OPERAT I N G THE
LI FT !
6. To raise the lift, use the foot pedal control to feed air to the lift. Once the lift reaches the desired height, return
the foot pedal to a neutral position.
7. Always secure the lift using the safety locking system by grabbing the orange / red safety bar and swinging it
down. Once a lock is in position, lower the lift using the foot pedal control until it rests on that lock.
(Continued On Next Page)
Copyright
2020
C
If the safety lock assembly does not engage, fully low er the
CAUTION:
lift and have an APlusLift qualified service technician immediately repair
the safety lock assembly or contact your distributor.
LIFT UNTIL THE SAFETY LOCKING SYSTEM IS WORKING PROPERLY.)
(WARNING: Make sure to only tighten the Front Wheel Vise enough
TM
Phone: 800-616-9618 Text: 425-300-2600 Email: [email protected]
www.apluslift.com
APlusLift MT1500 & MT1500X
I N ST ALLAT I ON M a nua l
(DO NOT USE THE
DO N OT DRI V E
15 of 20