Apollo 51000-300 Manuel

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Apollo 51000-300. Apollo 51000-300 4 pages. Wireless smoke alarm interconnect base

Imprimer la page

Apollo

51000-300

WIRELESS SMOKE ALARM INTERCONNECT BASE

GENERAL INFORMATION

The Wireless Smoke Alarm Interconnect Base part number 51000-300 is a 120V AC

powered sensor. It monitors the interconnect line on interconnected hardwired smoke

alarm systems and sends out a transmission when any of the smoke alarm units on the

same circuit enter an alarm state. The device has LEDs to visually indicate the status of the

interconnect base. A single CR2032 ba� ery provides backup power in the event that AC

power is lost on the alarm system circuit. The Wireless Smoke Alarm Interconnect Base

communicates with a compa� ble control panel and can send alarm, low ba� ery, AC power

loss, and supervisory messages to the system's receiver.

Contents of Carton:

• 1 � Wireless Smoke Alarm Interconnect Base

• 2 � 2" long 10-32 Screws

• 1 � CR 2032 3 Volt Coin Ba� ery

CR2032

COIN BATTERY

CR2032

10-32 X 2"

SCREWS

Figure 1. 51000-300 Kit

IMPORTANT: This device must be tested and maintained regularly. This device is intended

for use with compa� ble smoke alarms, but will not detect the presence of smoke, heat, or

 re directly.

✓ Note: Each of the smoke alarms part of interconnected smoke alarms must be:

• Present in every required loca� on per NFPA 72,11.5.1

• Con rmed as less than ten years from date of installa� on (or manufacture). Please

check label on the device or original smoke detector device manual.

• Hardwired to a single, common 120V AC circuit designated for interconnected smoke

alarms.

• Pass the manufacturer's stated tes� ng regimen to con rm proper interconnect

opera� on.

• Have fresh back-up ba� eries.

• On the list of compa� ble models (any model not listed may work but has not been

compa� bility tested).

• This device shall not be installed in loca� ons where the normal ambient temperature

is below 40F(4.4C) or exceeds 100F (37.8C), unless the alarm has been determined

capable of being used at installa� on points with higher or lower ambient temperatures.

• Please see sec� on at the end regarding informa� on on the proper installa� on of smoke

alarms that are intended to work with the Wireless Smoke Alarm Interconnect Base.

This device is not intended to work with smoke alarms paired with smoke alarm guards,

unless the combina� on has been evaluated and found suitable for this purpose.

Compatible Smoke Alarm Models

• BRK Brands Model 7010B: AC Powered Photoelectric Smoke Alarm with Ba� ery

Backup

• Firex Kidde Model i4618: Hardwire Ioniza� on Smoke Detector with Ba� ery Backup

• First Alert BRK Model 9120B: Hardwired Smoke Alarm with Ba� ery Backup

• Kidde Model i12040: 120V AC Wire-in Smoke Alarm with Ba� ery Backup

• USI Electric Model 5304: Hardwired Ioniza� on Smoke and Fire Alarm with Ba� ery

Backup

CAUTION: Before a� emp� ng installa� on, locate the primary electrical circuit that

powers the interconnected hardwired smoke alarm system and shut oﬀ or disconnect

power to this circuit. An electrical shock hazard is present if this electrical circuit is not

temporarily disabled during installa� on.

AVERTISSEMENT: Avant de commencer l'installa� on, trouver le circuit électrique

principal qui alimente le système câblé de détec� on de fumée interconnecté

et l'éteindre ou couper l'alimenta� on de ce circuit. Un risque d'électrocu� on

est présent si ce circuit électrique n'est pas temporairement coupé pendant

l'installa� on.

WARNING: Remember to turn on or reconnect power to the primary electrical circuit

that powers the interconnected hardwired smoke alarm system. The  re warning system

may be disabled if electrical power is not restored to the system.

ATTENTION : Ne pas oublier d'établir ou de rétablir le courant du circuit électrique

principal qui alimente le système câblé de détec� on de fumée interconnecté. Le

système d'alerte incendie serait inopérant si le courant électrique alimentant le

système n'était pas rétabli.

Install Wireless Interconnect Base

Select a smoke alarm that will be used to provide power and communicate to the

wireless interconnect base. Any smoke alarm that is within range of a compa� ble

wireless receiver can be selected if the smoke alarm is part of an interconnected

hardwired system.

Remove the exis� ng smoke alarm from the exis� ng moun� ng bracket. This is

usually done by twis� ng the alarm counter clockwise or clockwise from where it

is mounted.

APD0671 A160301

WIRELESS SMOKE ALARM INTERCONNECT BASE

MODEL 51000-300

WIRELESS SMOKE ALARM

INTERCONNECT BASE

WIRETAPS

EXISTING

SMOKE

ALARM

MOUNTING

BASE

ROTATE

COUNTER

CLOCKWISE

TO REMOVE

EXISTING

SMOKE

ALARM

Figure 2. Remove Exis� ng Smoke Alarm from Smoke Alarm Moun� ng Base

EXISTING SMOKE

ALARM

UNPLUG

SMOKE ALARM

FROM EXISTING

POWER PIGTAIL

Figure 3. Unplug Pigtail of Exis� ng Smoke Alarm

Unplug the exis� ng smoke alarm from the smoke alarm pigtail. Loosen the two screws

used to hold the exis� ng moun� ng bracket and remove it from the wall or ceiling.

REMOVE

EXISTING

SCREWS

Figure 4. Remove Exis� ng Smoke Alarm Moun� ng Bracket from Wall or Ceiling

WIRELESS SMOKE

ALARM INTERCONNECT

BASE

Figure 5. Install Wireless Smoke Alarm Interconnect Base between Wall and

Moun� ng Bracket

Place the interconnect base where the exis� ng moun� ng bracket was located. Make

sure the wire/wiretaps are inserted through the center opening of the smoke alarm

moun� ng bracket.

Place the exis� ng smoke alarm moun� ng bracket on top of interconnect base. Align the

interconnect base and the smoke alarm moun� ng bracket and replace the two screws

used to hold the bracket in place. Tighten all screws down.

✓ NOTE: It is suggested that the smoke alarm sensor LEDs be oriented towards the

EXISTING

POWER

PIGTAIL

MOUNT BRACKET

WITH LED'S AT BOTTOM

bo� om or in a manner that allows the LEDs on the unit to be visible.

Figure 6. Wiretaps/Wires, & Pigtail through Center

SMOKE

EXISTING SMOKE ALARM

MOUNTING BRACKET

ACCESS HOLE

IN WALL OR

CEILING

EXISTING

SMOKE

ALARM

POWER

PIGTAIL

REMOVE EXISTING SMOKE

ALARM MOUNTING

BRACKET FROM WALL OR

CEILING

WALL ACCESS HOLE

EXISTING

POWER

PIGTAIL

WIRETAPS (3)

(NOT CONNECTED)

EXISTING SMOKE ALARM

MOUNTING BRACKET

WIRELESS SMOKE

ALARM INTERCONNECT

BASE

EXISTING

SMOKE

ALARM

MOUNTING

BRACKET

WIRETAPS (3)

(NOT CONNECTED)