Datamax 220236-000 Manuel rapide

Parcourez en ligne ou téléchargez le pdf Manuel rapide pour {nom_de_la_catégorie} Datamax 220236-000. Datamax 220236-000 2 pages. Oc family of printers depot charger

Imprimer la page

OC 4-Up Charging Bracket

(220237-000)

Battery Charger LED Indicators

Description

Power LED Battery LED Error LED

Power off

Off

Power on. No

Green

Off

battery inserted.

Battery is charging. Green

Red

Off

Battery is 100%

Green

Off

full.

Battery charger

Green

Off

Red blinking

error.

Battery error.

Green

Off

Red blinking

Battery Charger Troubleshooting

Symptom

Possible Cause

Solution

Battery charger will

Defective battery.

Replace battery.

not charge the

battery.

Battery too hot or

Allow to adjust to

cold.

room temp.

Faulty LED.

Send in for repair.

Battery becomes

Defective battery.

Discontinue

hot.

charging and

remove battery.

Battery Error LED

Faulty condition

Remove battery

is displayed.

identified.

from charger and

re-insert.

Defective battery.

Replace battery.

No LEDs are

Power supply cord

Check power supply

displayed.

not connected.

connections.

Bad power supply.

Replace power

supply.

OC 5-Up Charging Bracket

(220236-000)

OC Desktop Cradle Charger

(210259-000)

Guidelines

General Guidelines

• The Charging Brackets are designed to be

used on a desktop or as a wall-mounted unit. It

is not intended for vehicle mounting.

• Position the chargers so there is enough room

to properly remove the printer(s) and batteries.

• The desktop cradle charger and charging

brackets take approximately 3-4 hours to

charge each printer. If multiple printers are

attached, the charge time remains at

approximately 3-4 hours per printer; however,

charge times may vary.

• The battery charger takes approximately six

hours to charge two batteries sequentially.

Charge times may vary.

• When mounting the charging bracket(s), only

mount them to wall studs.

Safety Guidelines

• Position the chargers so they are protected

from environmental elements such as direct

sunlight, moisture, high temperature, tools, and

boxes. Position the chargers in a secure area

in normal traffic patterns.

• Do not use the chargers if they appear

damaged.

• To reduce risk of electric shock, unplug the

chargers before cleaning.

• Batteries become warm to the touch during

charging. If the battery becomes too hot to

touch, discontinue charging and contact

Datamax-O'Neil.

• Use of any charger or battery not approved by

Datamax-O'Neil for use with their printers could

cause damage to the batteries or printer and

will void the warranty.

• Do not insert foreign objects into the chargers.

• Do not disassemble, incinerate, or short circuit

batteries, the chargers, or related components.

• Use appropriate hardware when mounting the

charging bracket(s). Datamax-O'Neil does not

accept liability for improperly mounted charging

brackets. Datamax-O'Neil does not accept

liability for poorly placed printers and/or

chargers.

Mounting the 4-Up and 5-Up

Charging Brackets

If the charging brackets will be mounted on a

vertical surface or on a wall, use the following

procedure to mount them:

1. Locate the wall studs.

2. Use the charging bracket as a template to

mark the mounting holes on the mounting

surface. Use both the upper and lower slots to

mount the charging bracket to the mounting

surface. There should be a minimum of four

mounting points. For guidelines on mounting,

see the Guidelines in the previous section.

3. Drill the mounting holes at the marked

locations. When drilling the mounting holes,

verify that you drill the holes into the stud.

Warning: Use caution when drilling the

mounting holes and when mounting the

charging brackets onto a wall.

4. Attach the charging bracket to the mounting

surface as follows:

Wood Surface: Use four #10 pan head wood

screws with washers (not included). #10

wood screws should not be used on any

other type of surface.

Drywall Surface: Use four #10 pan head

toggle bolts (not included).

5. Verify the charging bracket is level and secure.

6. Thread the screws through the washers,

charging bracket, and into the mounting holes,

and tighten securely. Make sure the charging

bracket is flush to the wall and there are no

pinched cables.