DVIGear DVI-TPS-TX90 Manuel de démarrage rapide

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} DVIGear DVI-TPS-TX90. DVIGear DVI-TPS-TX90 2 pages. Multiport tps extender

Imprimer la page
Maximum Cable Lengths
Resolution
Clock Freq.
CAT-5e
1024x768 @60Hz
65.00 MHz
328.1 ft.
1280x720p @60Hz
73.84 MHz
328.1 ft.
1920x1080i @60Hz
74.25 MHz
328.1 ft.
1280x1024 @60Hz
108.00 MHz
328.1 ft.
1920x1080p @60Hz
148.50 MHz
328.1 ft.
1920x1200 @60Hz
152.90 MHz
328.1 ft.
1600x1200 @60Hz
162.00 MHz
328.1 ft.
Note 1: With Long Reach firmware installed. This firmware supports pixel clock frequencies up to 148.5 MHz.
Please contact DVIGear technical support or your dealer to change or upgrade device firmware.
Note 2: CAT6A S/FTP (550 MHz) cable must be used to achieve these distances.
Installation
WARNING: Ethernet ports are designed to connect to 10/100 Ethernet products. Do not connect
Ethernet appliances to TPS IN or TPS OUT ports as it may result in damage to the equipment.
1.
Set the switch on the front panel to the Normal position.
2.
Connect a CAT-X twisted pair cable to the TPS OUT on the transmitter unit.
3.
Connect the other end of the CAT-X twisted pair cable to the TPS IN on the receiver unit.
4.
Connect an HDMI signal source to the HDMI IN port on the transmitter unit.
5.
Connect an HDMI display device (e.g. projector) to the HDMI OUT on the receiver unit.
6.
To use the bi-directional pass-through data lines, connect desired devices to the transmitter
and receiver units. See examples in table
7.
Connect the supplied External AC Power Adapter to either unit. The other unit will
automatically receive power over the twisted pair cable connected between the TPS ports.
Use LAN cables to connect an Ethernet device (e.g. switch) to the Ethernet port on the Transmitter unit
Ethernet
and a network device (e.g. projector) to the Ethernet port on the Receiver unit.
Use serial cables to connect a controller unit (e.g. touch panel) to the RS-232 port on the Transmitter unit,
RS-232
and serial controlled device (e.g. projector) to the RS-232 port on the Receiver unit.
Connect the supplied IR Transmitter to the IR OUT port of the transmitter unit.
Infra-Red
Connect the supplied IR Receiver to the IR IN port on the Receiver unit.
Note 3: Examples of optional devices that are supported over the MultiPort TPS twisted pair link.
4
CAT-5e
(1)
CAT-6A
(2)
(100 m)
524.9 ft.
(160 m)
393.7 ft.
(120 m)
590.6 ft.
(100 m)
524.9 ft.
(160 m)
393.7 ft.
(120 m)
590.6 ft.
(100 m)
524.9 ft.
(160 m)
393.7 ft.
(120 m)
590.6 ft.
(100 m)
524.9 ft.
(160 m)
393.7 ft.
(120 m)
590.6 ft.
(100 m)
492.1 ft.
(150 m)
393.7 ft.
(120 m)
557.7 ft.
(100 m)
N/A
393.7 ft.
(120 m)
(100 m)
N/A
393.7 ft.
(120 m)
(3)
below.
DVI-TPS-TX90_RX90-QSG-01 / August.2012
CAT-6A
(1)(2)
(180 m)
Introduction
DVIGear's MultiPort TPS Extender supports long-range extension of HDMI (v1.4) signals over a single CAT-X
(180 m)
twisted pair (TP) cable at distances of up to 180 meters (590 ft.). These units also support bi-directional
RS-232, Infra-Red, 10/100 BaseT Ethernet, and PoE over the same twisted pair link.
(180 m)

Typical Application

(180 m)
(170 m)
N/A
N/A
12V DC
Power Adaptor
Quick Start Guide
MultiPort TPS Extender
IR cable
IR Transmitter
Serial
cable
Touch panel
Blu-Ray or DVD Player
HDMI cable
DVI-TPS-TX90
LAN
Internet
Ethernet switch
LAN
DVI-TPS-RX90
Remote powered
IR cable
IR Receiver
MultiPort TPS Extender: DVI-TPS-TX90 and DVI-TPS-RX90
DVI-TPS-TX90
DVI-TPS-RX90
TPS connection
CAT-X up to 180m
Serial cable
HDMI
cable
LAN
HD Projector
Projection screen
1