Frigidaire FCRS201RFB2 Manuel d'utilisation et d'entretien - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et d'entretien pour {nom_de_la_catégorie} Frigidaire FCRS201RFB2. Frigidaire FCRS201RFB2 11 pages. Commercial freezer/refrigerator glass door refrigerator

Imprimer la page

Electrical

Information

These

guidelines

must be followed

to ensure

that safety

mechanisms

in the design

of this appliance

will operate

properly.

Avoid fire hazard or

electric shock. Do not use an extension cord

or an adapter

plug.

Do not remove

any

prong from the power cord.

Grounding type

walmreceptacle

Power suppmy

cord with 3-prong

grounding pmug

•

Refer

to the serial

plate

for

correct

electrical

rating.

The

power

cord

of the appliance

is equipped

with

a three-prong

grounding

plug for protection

against

shock

hazards.

It must

be plugged

directly

into its own properly

grounded

three-prong

receptacle,

protected

with a 15 amp time delay fuse or circuit

breaker.

The receptacle

must

be installed

in accordance

with

the local codes and ordinances.

Consult

a qualified

electrician.

Receptacles

with Ground

Fault Circuit

Interrupters

(GFCI)

are

NOT

RECOMMENDED.

NOT

USE

EXTENSION

CORD

OR AN ADAPTER

PLUG.

•

If the

voltage

varies

10 percent

or more,

appliance

performance

may

be affected.

Operating

the appliance

with

insufficient

power

can damage

the motor.

Such

damage

not covered

under the warranty.

If you suspect

your voltage

high or low, consult

your

power

company

for testing.

•

To prevent

the appliance

from

being

turned

off accidentally,

do not plug the unit into an outlet

controlled

by a wall switch

or pull cord.

•

DO NOT pinch,

knot,

or bend

the power

cord

in any manner.

Other

Precautions

•

NEVER

unplug

the appliance

by pulling

on the power

cord.

Always

grip

the

plug

firmly

and

pull straight

out from

the

receptacle.

•

To avoid

electrical

shock,

unplug

the

appliance

before

cleaning.

NOTE:

Turning

the control

to "OFF"

turns

off the compressor

but does

not disconnect

power

to other

electrical

components.

Installation

and Setup

Inspection for Damage

inspect

the underside

of the cabinet

and packaging

for damage

such as a fork truck

can cause.

If hidden

damage

is found

after

uncrating,

immediately

call the delivery

carrier

and request

inspection.

Retain

all packaging

and crating

materials

until the

inspection

is complete.

Uncrating

and Set-up

• Remove

carton

and all loose parts

from inside

of the unit.

• Tip the unit onto

its back with the help of one assistant.

Lay

the

unit

gently

to rest

on blocks

to avoid

damaging

the

condensate

drain

hose,

and the plastic

raceway

that covers

the evaporator

tubing

on the back of the cabinet.

• Remove

and discard

the two (2) wood

skids from the bottom

and the four (4) screws

(see the Fig. 1).

• Remove

the bottom

door hinge

and screw

on the lower left

hand

side of the cabinet

used to support

the glass

door

during

shipping

using

a 3t8 socket

wrench

(see

Fig. 2).

• Remove

the package

containing

the casters

from the unit. This

package

will contain

the following

items:

•

Two (2) caster

rail supports

(A)

•

Two (2) spacer

plates

(B)

•

Eight

(8) carriage

bolts (C)

•

Four (4) bolts (D)

•

Four (4) washers

(E)

•

Eight (8) locking

nuts (F)

•

Two (2) swivel

casters

(G)

•

Two (2) fixed casters

with brakes

(H)

( o

o :30:]

Figure

Wood

Skid

Figure