AUSTRALIAN MONITOR ACM250 Spécifications - Page 2
Parcourez en ligne ou téléchargez le pdf Spécifications pour {nom_de_la_catégorie} AUSTRALIAN MONITOR ACM250. AUSTRALIAN MONITOR ACM250 2 pages. 250w, 6 channel mixer amplifier
Également pour AUSTRALIAN MONITOR ACM250 : Manuel d'utilisation (7 pages)
Imprimer la pageEngineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (
NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233
TAS Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Fax: (08) 8352 4488 Export Enquiries: [email protected]
Power Output
Maximum Load
Power Bandwidth
Frequency Response
Total Harmonic Distortion
Signal To Noise Ratio
Tone Controls
Bass @ 100Hz: Boost +12dB Cut -12dB; Mid @ 600Hz: Boost +12dB, Cut -12dB;
Inputs
Six mic/aux universal inputs with XLR female mic sockets and dual RCA Phono aux sockets
Input Sensitivity Mics: 1mV @ 200 Ohms; Aux 1 - 5: 75mV @ 47K Ohms; Aux 6: 300mV @ 47K Ohms
Outputs
Speaker: 100, 70 Volts, 4 Ohms; Tape: 350mV @ 10K Ohms; Line: Balanced 700mV
Phantom Power
Controls
6 Input channel gain controls, 1 Bass control, 1 Mid Control, 1 Treble control,
Indicators
Power Source
Power Consumption
Protection
Dimensions/Weight
Rack Mounting
Tone Generators
Muting
Built-in VOX muting. Channels 1 and 2 will mute channels 3, 4, 5 and 6
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The mixer amplifier shall have six universal inputs each comprising of a balanced microphone with XLR
female sockets and an auxiliary input using dual RCA sockets. A balanced XLR output to drive addi-
tional power amplifiers shall also be provided.
The amplifier master section shall include one master gain control, three EQ controls, one with 12dB of
cut and boost at 100Hz, one with 12dB cut and boost at 600Hz and the other with 9dB of cut and boost
at 10kHz. Speaker outputs shall be transformer isolated at 100 volt, 70 volt and 4 ohms. The amplifier
must be capable of delivering 250 watts RMS into a 40 inductive ohm load, with less than 0.5% distor-
tion measured at 1kHz and with system hum and noise less than -74dB.
The amplifier shall be an Australian Monitor Installation Series model ACM250.
), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia
ABN 78 001 345 482
-74dB with all controls at their centre position
Treble @ 10kHz: Boost +9dB Cut -9dB
1 Master gain control, Phantom Power on/off switch (on rear panel)
AC 230/240V - 60Hz, 110V - 50Hz (special) 3 pin IEC connector
Current Limiter protection, plus AC and DC fuses
88mm H x 480mm W x 330mm D (Chassis Dimensions only). 15kg
Built-in four tone generator module.
Includes Bell, Pre-Announce, Alert and Evac Tones
Website: www.australianmonitor.com.au
250 watts RMS
40 Ohms @ 100 Volts
60Hz - 15kHz < 0.5% THD
60Hz - 15kHz (± 3dB)
0.5% @ 1kHz rated power
18 Volts DC on all Mic inputs
Power "on" and "Protect" LED
400 Watts
Standard