Gage Bilt 1753 Manuel d'instructions original - Page 11
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions original pour {nom_de_la_catégorie} Gage Bilt 1753. Gage Bilt 1753 20 pages. Installation tool
Imprimer la page
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat-o-seal, installed in tool head. Severe
personal injury could result.
WARNING:
Use CAUTION when removing screws or the air bleeder assembly (704153). Hydraulic oil may be under pressure.
CAUTION:
Before filling handle assembly (722132), air piston assembly (704121) must be all the way down.
CAUTION:
When forcing piston rod assembly (722133) downward, with head cylinder assembly (752119) removed, hydraulic oil
will eject forcibly from handle assembly (722132).
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
Note:
•
Air Bleeder Assembly (704153) (sold separately) is required.
FILLING & BLEEDING VIDEO AVAILABLE AT: http://www.gagebilt.com/rivet_tools_videos.php
BLEEDING PROCEDURE:
To replace a small amount of oil,
head cylinder assembly (752119). Install air bleeder assembly (704153) and connect tool to air line. Cycle ten times to fully circulate oil
through hydraulic system.
(402482) and stat-o-seal (S572) on head cylinder assembly (752119). Torque 35-40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten. This
will ensure the removal of any air from the hydraulic system and its replacement with oil.
FILLING AND BLEEDING PROCEDURE: (Required after tool has been dismantled).
1. Place piston rod wrench assembly (704149) in power cylinder (722134) and carefully push piston rod assembly (722133) and air piston
assembly (704121) completely down.
2. Fill handle assembly (722132), power cylinder (722134) and the oil passage on top of handle assembly (722132) with automatic
transmission oil, Dexron® III or equivalent. When looking at the top of the handle assembly (722132), the oil passage is the hole that
is counterbored for o'ring (S832). See image below.
3. Push piston (752507) full forward in head cylinder assembly (752119), then attach head cylinder assembly (752119) with care,
ensuring gasket (704129) and o'ring (S832) are properly installed. Apply Loctite® 242 to button head cap screws (A-928) and torque
uniformly to 40 inch lbs. (4.52 Nm) to prevent leakage around gasket (704129).
4.
ENSURE TOOL IS DISCONNECTED FROM AIR.
assembly (752119). Install air bleeder assembly (704153) (sold separately) and connect tool to air line. Cycle ten times to fully circulate oil
through hydraulic system.
5.
DISCONNECT AIR FROM TOOL.
(S572) on head cylinder assembly (752119). Torque 35-40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten.
6. Reconnect air and cycle tool ten more times. Check tool stroke using instructions a thru c and diagrams below. We recommend
using dial calipers.
a. With the actuator assembly-air (704130) released check dimension (A).
b. Holding actuator assembly-air (704130) in, check dimension (B).
c. Subtract dimension (A) from dimension (B). If stroke doesn't check .590" (15.0 mm) min. (See figures below) follow bleeding
procedure above.
For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke.
Please contact Gage Bilt for more information.
GB722 S/N: 1753 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
FILLING AND BLEEDING PROCEDURE:
DISCONNECT AIR FROM TOOL.
DISCONNECT AIR FROM TOOL,
Remove button head cap screw (402482) and stat-o-seal (S572) from head cylinder
Remove air bleeder assembly (704153) and install button head cap screw (402482) and stat-o-seal
Oil Passage hole
O'ring (S832)
***Keep air
hole free
from oil***
Remove button head cap screw (402482) and stat-o-seal (S572) from
remove the air bleeder assembly (704153), and reinstall button head cap screw
Handle Assembly and
Power Cylinder hole
Images may not reflect actual tool.
11
Bleeder hole on head cylinder
assembly (752119) Button head
cap screw (402482) & stat-o-
seal (S572)
Air
Bleeder
Assembly
(704153)
REV. 5/22