Dyna-Glo Delux RMC-FA300DGD Mode d'emploi et manuel des pièces détachées - Page 4

Parcourez en ligne ou téléchargez le pdf Mode d'emploi et manuel des pièces détachées pour {nom_de_la_catégorie} Dyna-Glo Delux RMC-FA300DGD. Dyna-Glo Delux RMC-FA300DGD 12 pages. Delux propane construction heater
Également pour Dyna-Glo Delux RMC-FA300DGD : Mode d'emploi et manuel des pièces détachées (11 pages)

Imprimer la page

Dyna-Glo Delux RMC-FA300DGD Mode d'emploi et manuel des pièces détachées

1. Troubleshooting Chart

ProFitter

& Dyna-Glo

Dyna-Glo

Delux Operating Instructions and Parts Manual

ProFitter

Dyna-Glo

Propane Construction Heater

Installation

Review and under-

stand all of the

warnings in the Safety Information

Section on pages 1–3. They are required to

Section on pages 1–3. They are required

operate this heater safely. Follow all local

to operate this heater safely. Follow all

and state codes when operating this

local and state codes when operating

heater.

this heater.

After installing

all gas piping, and

making the proper connections, be sure

to check for leaks. Apply a 50/50

mix ture of dish soap and water to

mixture of dish soap and water to

all connections. Bubbles forming are

evidence of a leak. Be sure to correct

all leaks at once!

1. Provide propane supply system as

outlined above.

2. Connect POL fitting on hose/regulator

assembly to propane tank(s) by turn ing

assembly to propane tank(s) by turn-

the fitting COUNTER CLOCKWISE

ing the fitting COUNTERCLOCKWISE

into the threads on the valve on top of

into the threads on the valve on top

the tank. Finish by tightening firmly,

of the tank. Finish by tightening

using 7/8" (22.2 mm) wrench.

firmly, using 7/8" wrench.

IMPORTANT: To protect the regulator

from weather damage, tighten the

fitting with the black adjustment knob

pointing down.

POL Fitting

Supply

Valve

Propane/LP

Tank

Adjustment Knob

(Pointing Down)

Figure 3 – Regulator with Vent Pointing

Down

3. Connect female end of hose to the

inlet connector of the heater, and

tighten firmly with a wrench.

IMPORTANT: Use extra piping or hose

if necessary to connect the heater to the

gas supply, but always use the regulator

supplied with the heater.

For Technical Support or Troubleshooting, Call: 1-877-447-4768

For Technical Support or Troubleshooting, Call: 1-877-447-4768, 8:30 am - 4:30 pm CST

Operating Instructions and Parts Manual

& Dyna-Glo

Figure 4 – Hose and Inlet Connector

4. Open supply valve on propane tank(s)

SLOWLY.

NOTE: If this valve is not opened slowly,

the excess flow check valve on the tank

the excess flow check valve on the

will interrupt the gas flow. If this

tank will interrupt the gas flow. If this

happens, close the supply valve and

reopen slowly.

5. Adjust the regulator to between 7

and 10 PSIG.

PSIG or below 7 PSIG, or the heater may

not operate properly.

6. Check all connections for leaks.

leaks. Apply a 50/50 solution of liquid

dish soap and water to check all

connections. Correct all leaks

Hose

connections. Correct all leaks

Hose

immediately.

7. Close propane supply valve.

7. Close propane supply valv

Regulator

Ventilation

Regulator

Ventilation

ventilation requirements. If these

guidelines are not followed, carbon

monoxide poisoning can occur. Always

provide proper amounts of fresh air

before operating this heater.

Provide at least three square feet of

Provide at least three square feet (0.28 m²)

fresh, outside air for each 100,000

of fresh, outside air for each 100,000 BTU/

BTU/Hr of rating. This heater requires

Hr of rating. This heater requires

a fresh air opening of at least 11.25

a fresh air opening of at least 11.25 square

square feet. Provide extra fresh air if

feet (1.05 m²). Provide extra fresh air if

more heaters are being used.

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

Hose

Inlet Connector

Do not adjust the

regulator above 10

Never use an open

flame to check for

Always follow the

minimum fresh air

RMC-FA300PF/DG/DGD

RMC-FA300DGD

Operation

Review and under-

stand all of the

warnings in the Safety Information

Section, on pages 1–3. They are required

to operate this heater safely. Follow all

local and state codes when operating this

local and state codes when operating

heater.

this heater.

TO START HEATER

1. Follow all safety, installation and

ventilation instructions in this

manual.

2. Position the heater on a stable and

level surface, and be sure that no

drafts blow into the inlet or outlet

of the heater.

3. Plug the power cord of the heater

into a three hole grounded extension

cord. Be sure that the extension cord

is at least 6 feet long, and is UL listed.

EXTENSION CORD SIZE

REQUIREMENT

• Up to 50 feet (15.2 m) long, use 18

• Up to 50 feet long, use 18 AWG

AWG rated cord.

rated cord.

• 51 to 100 feet (15.5 - 30.5 m) long,

• 51 to 100 feet long, use 16 AWG

use 16 AWG rated cord.

rated cord.

• 101 to 200 feet (130.8 - 61 m) long,

• 101 to 200 feet long, use 14 AWG

use 14 AWG rated cord.

rated cord.

4. Plug extension cord into a 120 volt/60

hertz, three hole grounded outlet.

5. Open supply valve on propane tank(s)

SLOWLY.

NOTE: If this valve is not opened slowly,

the excess flow check valve on the

the excess flow check valve on the tank

tank will interrupt the gas flow. If this

will interrupt the gas flow. If this

happens, close the supply valve and

reopen slowly.

6. Adjust the regulator to between 7

and 10 PSIG.

NOTE: The higher regulator setting

will enable the heater to produce

more heat.