Great Lakes Biostar Scan Manuel d'utilisation - Page 14

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Great Lakes Biostar Scan. Great Lakes Biostar Scan 16 pages.

Imprimer la page

BIOSTAR

Troubleshooting & Fabrication Tips

Use the following tips to address:

BIOSTAR

Troubleshooting & Fabrication Tips

BIOSTAR

Troubleshooting & Fabrication Tips

Use the following tips to address:

• Air leaks

• Poor adaptation

• Blowouts

• Material thinning • Mounted model too high for pellet cup

Use the following tips to address:

• Air leaks

Use the following tips to address:

• Poor adaptation

• Blowouts

• Material thinning • Mounted model too high for pellet cup

• Air leaks

• Poor adaptation

• Air leaks

• Poor adaptation

• Blowouts

• Material thinning • Mounted model too high for pellet cup

• Blowouts

• Material thinning • Mounted model too high for pellet cup

If gasket does not move freely,

remove it and clean with a small

If gasket does not move freely,

amount of liquid dish soap

remove it and clean with a small

applied and removed with a dry

If gasket does not move freely,

amount of liquid dish soap

If gasket does not move freely,

paper towel. Lubricate pins and

remove it and clean with a small

applied and removed with a dry

remove it and clean with a small

springs and replace gasket.

amount of liquid dish soap

paper towel. Lubricate pins and

amount of liquid dish soap

applied and removed with a dry

springs and replace gasket.

applied and removed with a dry

paper towel. Lubricate pins and

springs and replace gasket.

Remove pellets from cup, make sure the 12 air

escape holes are not plugged. Use a .036"

Remove pellets from cup, make sure the 12 air

diameter or smaller wire to open plugged holes.

escape holes are not plugged. Use a .036"

Remove pellets from cup, make sure the 12 air

diameter or smaller wire to open plugged holes.

Remove pellets from cup, make sure the 12 air

escape holes are not plugged. Use a .036"

diameter or smaller wire to open plugged holes.

Great Lakes recommends: all soft or semi-soft material should be formed on the

platform. See photo on left: the base of the model is even and ﬂat. Use pellets for hard

Great Lakes recommends: all soft or semi-soft material should be formed on the

material (see photo on right).

platform. See photo on left: the base of the model is even and ﬂat. Use pellets for hard

Great Lakes recommends: all soft or semi-soft material should be formed on the

material (see photo on right).

Great Lakes recommends: all soft or semi-soft material should be formed on the

platform. See photo on left: the base of the model is even and ﬂat. Use pellets for hard

material (see photo on right).

For fabrication videos, tips and techniques, visit

• Material heating unevenly

Remove pins and springs.

Lubricate with small amount of

Remove pins and springs.

grease (016-021). Replace pins

Lubricate with small amount of

and springs and insert gasket.

Remove pins and springs.

grease (016-021). Replace pins

Depress gasket ring once or twice

Remove pins and springs.

Lubricate with small amount of

and springs and insert gasket.

Lubricate with small amount of

to make sure it moves freely.

grease (016-021). Replace pins

Depress gasket ring once or twice

grease (016-021). Replace pins

and springs and insert gasket.

to make sure it moves freely.

and springs and insert gasket.

Depress gasket ring once or twice

to make sure it moves freely.

Make sure all pellets are removed from edge

of cup where the chamber locks into place.

Make sure all pellets are removed from edge

Pellets should be even with top of pellet cup.

of cup where the chamber locks into place.

Make sure all pellets are removed from edge

Pellets should be even with top of pellet cup.

Make sure all pellets are removed from edge

of cup where the chamber locks into place.

Pellets should be even with top of pellet cup.

greatlakesdentaltech.com/techniques.

Ask for a Heating Times &

Applications Guide to help you get the

Ask for a Heating Times &

best results from your BIOSTAR.

Applications Guide to help you get the

Ask for a Heating Times &

best results from your BIOSTAR.

Applications Guide to help you get the

best results from your BIOSTAR.

Performing a Cold Test:

A) Turn unit on. Make sure platform is

Performing a Cold Test:

in place. Clamp a sheet of 2mm (or

thicker) hard material onto pressure

A) Turn unit on. Make sure platform is

Performing a Cold Test:

chamber. Secure clamping frame.

in place. Clamp a sheet of 2mm (or

thicker) hard material onto pressure

A) Turn unit on. Make sure platform is

B) Enter 5 seconds heating time. Swing

chamber. Secure clamping frame.

in place. Clamp a sheet of 2mm (or

the heating element over the material

thicker) hard material onto pressure

to activate heat. Immediately return

B) Enter 5 seconds heating time. Swing

chamber. Secure clamping frame.

heating element to rest position.

the heating element over the material

to activate heat. Immediately return

B) Enter 5 seconds heating time. Swing

C) Swing pressure chamber over the

heating element to rest position.

the heating element over the material

model platform. Activate air pressure.

to activate heat. Immediately return

C) Swing pressure chamber over the

heating element to rest position.

D) If you hear a constant rush of air

model platform. Activate air pressure.

during pressurization, contact your

C) Swing pressure chamber over the

customer service representative.

D) If you hear a constant rush of air

model platform. Activate air pressure.

during pressurization, contact your

customer service representative.

D) If you hear a constant rush of air

during pressurization, contact your

customer service representative.

preset at 60lbs. or 4-5 bars

Note: The BIOSTAR is

of working pressure.

preset at 60lbs. or 4-5 bars

Note: The BIOSTAR is

of working pressure.

preset at 60lbs. or 4-5 bars

of working pressure.

Make sure the heating

surface is parallel to the

Make sure the heating

heating element. See

surface is parallel to the

Maintenance Tips to adjust.

Make sure the heating

heating element. See

Make sure the heating

surface is parallel to the

Maintenance Tips to adjust.

surface is parallel to the

heating element. See

Maintenance Tips to adjust.

For mounted models, remove the majority of

pellets. Leave only enough under the model

For mounted models, remove the majority of

to allow air to ﬂow. Build up the pellets,

pellets. Leave only enough under the model

leaving exposed only the area to be covered

For mounted models, remove the majority of

to allow air to ﬂow. Build up the pellets,

For mounted models, remove the majority of

by acrylic material.

pellets. Leave only enough under the model

leaving exposed only the area to be covered

pellets. Leave only enough under the model

to allow air to ﬂow. Build up the pellets,

by acrylic material.

to allow air to ﬂow. Build up the pellets,

leaving exposed only the area to be covered

by acrylic material.

1-800-828-7626

greatlakesortho.com

1-800-828-7626

greatlakesortho.com

1-800-828-7626

greatlakesortho.com