Dynabrade 53103 Fonctionnement et entretien - Page 3

Parcourez en ligne ou téléchargez le pdf Fonctionnement et entretien pour {nom_de_la_catégorie} Dynabrade 53103. Dynabrade 53103 9 pages. Pistol grip drill central vacuum

Imprimer la page

Important: To keep tool safe a preventative maintenance program is recommended whenever portable power tools are used. The program

should include inspection of air supply lines, air line pressure, proper lubrication and repair of tools. Refer to ANSI B186.1 for additional

maintenance information.

• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your

air tool.

• It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility

of misuse due to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 10681 Air Filter-Regulator-

Lubricator (FRL) – Provides accurate air pressure regulation and two stage filtration of water contaminant's.

• Grease the planetary gear assembly with the 95542 Grease by applying 1 plunge with the 95541 Grease Gun after every 50 hours of

use for maximum gear life.

• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the

drip rate on the filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.

Routine Preventative Maintenance:

• Check free speed of Pistol Grip Drill using a tachometer after every service or repair.

Caution: Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing

acids, esters, ketones, chlorinated hydrocarbons or nitro carbons.

Caution: DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40

• A Motor Tune-Up Kit (P/N 96047) is available which includes high wear and medium wear motor parts.

• Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification

information i.e.: Model #, S/N, and RPM. (See Assembly Breakdown)

• Blow air supply hose out prior to initial use.

• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.

• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.

After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to

lubricate air motor. Check for excessive tool vibration.

Handling and Storage:

• Use of tool rests, hangers and/or balancers is recommended.

• Protect tool inlet from debris (see Notice below).

• DO NOT carry tool by air hose, or near the tool throttle.

• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.

• Store accessories in protective racks or compartments to prevent damage.

All Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping to our customers. If a Dynabrade tool develops

a performance problem and an inherent defect is found during normal use and service, Dynabrade will warrant this tool against defects in workmanship and materials for

the lifetime of the tool. Upon examination and review at our factory, Dynabrade shall confirm that the tool qualifies for warranty status, and will repair or replace the tool at

no charge to the customer. Normally wearable parts and products are NOT covered under this warranty. Uncovered items include bearings, contact wheels, rotor blades,

regulators, valve stems, levers, shrouds, guards, O-rings, seals, gaskets and other wearable parts. Dynabrade's warranty policy is contingent upon proper use of our tools

in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment that has been subjected to misuse, negligence, accident or

tampering in any way so as to affect its normal performance. To activate lifetime warranty, customer must register each tool at www.dynabrade.com. Dynabrade will not

honor lifetime warranty on unregistered tools. A one-year warranty will be honored on all unregistered portable pneumatic power tools. Lifetime warranty applies only to

portable pneumatic tools manufactured by Dynabrade, Inc. in the USA. Lifetime warranty applies only to the original tool owner; warranty is non-transferable.

Model

Motor

Number

hp (W)

RPM

53103

.7 (522)

3,400

53104

.7 (522)

4,500

53105

.7 (522)

950

53106

.7 (522)

950

Maintenance Instructions

Lifetime Warranty

Machine Specifications

Air Inlet

Sound

Air Flow Rate

Thread

Level

SCFM (LPM)

1/4" NPT

84 dB(A)

40 (1130)

1/4" NPT

84 dB(A)

40 (1130)

1/4" NPT

84 dB(A)

40 (1130)

1/4" NPT

84 dB(A)

40 (1130)

Air Pressure

Hose I.D.

PSIG (Bars)

Size

90 (6.2)

3/8" (10 mm)

90 (6.2)

3/8" (10 mm)

90 (6.2)

3/8" (10 mm)

90 (6.2)

3/8" (10 mm)

Weight

Length

Pound (kg)

Inch (mm)

4 (1.8)

10-3/8 (264)

5-7/8 (149)

4 (1.8)

10-3/8 (264)

5-7/8 (149)

4.4 (2.0)

12-1/4 (310)

5-7/8 (149)

4.4 (2.0)

12-1/4 (310)

5-7/8 (149)

Height