Dynabrade 61300 Manuel d'utilisation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Dynabrade 61300. Dynabrade 61300 6 pages. Portable vacuum system
Également pour Dynabrade 61300 : Manuel d'utilisation (6 pages)
Imprimer la pageKeep machine clean to ensure optimum performance. After each
use, lift off vacuum head and knock dust from filter. After one hour
of continuous use, lift out the Motorhead/Vacuum Head Assembly
and check the amount of dust accumulated in the unit. Remove the
dust bag if necessary and replace with a new one. We recommend
a soft brush to clean the filter. DO NOT USE A BLOW GUN.
Decrease in Vacuum Performance
1. Clean the filter thoroughly and as often as necessary. The
filter used inside is water resistant and washable. To prevent
damage, do not use high pressure or solvent to wash the filter.
R E M O V A L / I N S TA L L AT I O N O F M O T O R H E A D F R O M M A I N A S S E M B LY
If the filter element becomes clogged or to clean the inner portions
of the drum (canister) the Motorhead Assembly must then be
removed to perform cleaning. When removal becomes necessary for
cleaning or other service, follow the procedures described below.
Removal
1. Unplug the unit before attempting service or maintenance
work.
2. Remove Top Lid by unlatching (2) hinges.
Unit has a Tilt-n-Clean feature to aid in overall functionality of the
work equipment and work environment:
1. Unplug the unit before attempting service or maintenance
work.
2. Unclamp and remove Motorhead/Vacuum Head Assembly.
Drum (canister) is now able to be tilted backwards and
emptied. Dispose of debris properly.
Swivel Adapter
P/N 96573
Cuff
For Older Two-Hand Tools
Insert
P/N 95895
O P E R AT I N G T I P S A N D T R O U B L E S H O O T I N G
T I LT- N - C L E A N O P E R AT I O N I N S T R U C T I O N
9 4 9 4 1 C O A X I A L V A C U U M H O S E A S S E M B LY
1-1/4" Vac Hose
Cuff with Air Line Exit
Air Line Assembly - 28 cm of Air Line
Assembly will Extend Past the Cuff
Dynabrade Coupler
P/N 94960
Dynabrade Male Plug
P/N 95675
2. If the filter (P/N 64684) should become damaged or badly
clogged and cannot be cleaned, replace with a new one.
3. Check all the vacuum lines for blockage or leakage.
Vacuum Stops During Use
1. This vacuum is equipped with a Electronic Thermal Protection
Device. If the vacuum stops and the red indicator light appears
ON, the unit has shut down as a result of increased
temperature. Once the unit has regained a temperature that is
allowable for operation the vacuum will resume operation.
3. Use a conventional vacuum cleaner to clean entire inside of
Motorhead/Vacuum Head Assembly and drum (canister).
Upon completion of the service work, install top lid according to
the following procedure:
Installation
1. Place cleaned unit onto the drum (canister) and latch (2)
hinges to properly attach the lid. Unit is now ready for
operation.
3. Or, Pull side release hinges away from the drum (canister)
and remove the entire drum (canister) from the trolley. With
drum (canister) removed dispose of debris properly.
Cuff with Air
1-1/4" Vac Hose
Line Exit
35 cm of Air
Line Assembly
will Extend Past
the Cuff
PAGE 3
1-1/4" Vac Hose
Cuff
Dynabrade Female Plug
P/N 95677