2gig Technologies 2GIG-DW30-345 Instructions d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} 2gig Technologies 2GIG-DW30-345. 2gig Technologies 2GIG-DW30-345 4 pages. Outdoor wireless contact sensor

2gig Technologies 2GIG-DW30-345 Instructions d'installation
Specifications
Wireless Signal Range
Code Outputs
Transmitter Frequency
Unique ID Codes
Supervision Interval
External Input
Magnet Dimensions (L x W x H)
Magnet Type
Magnet Gap
Sensor Dimensions (L x W x H)
Housing Material
Color
Operating Temperature
Relative Humidity
IP Rating
Battery (Included)
Certifications
4 Copyright © 2018 Nortek Security & Control LLC
350 ft (106.7 m) open air
with Wireless Control
Panel
Open, Restore,
Supervisory, Low
Battery, External Open,
External Restore,
Tamper, tamper Restore
345 MHz
Over one (1) million
different code
combinations
70 minutes.
Accepts N/C dry contact
devices
4.06 x 0.98 x 1.1" (103 x
25 x 28 mm)
Rare Earth
Up to 2"
4.57 x 2.13 x 1.54" (116 x
54 x 39 mm)
ASA
Black
-40ºF to 150 ºF (-40ºC
to 66 ºC)
0 ~ 100%
Tested to IP56
Two (2) Lithium AA
FCC, IC
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. Ľexploitation est autorisée aux deux conditions suivantes:
(1) ľappareil ne doit pas produire de brouillage, et (2) ľutilisateur de ľappareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible ďen
compromettre le fonctionnement.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules and Regulations as Part 15 devices as well as
Industry Canada license exempt RSS Rules and Regulations. Operation is subject to the
following two (2) conditions: This device may not cause harmful interference. This device
must accept any interference received, including interference that may cause undesired
operation.
INDUSTRY CANADA (IC) COMPLIANCE
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device. Repairs to certified equipment should be made by
an authorized Canadian maintenance facility designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material
and workmanship for two (2) years. This warranty extends only to wholesale customers
who buy direct from Nortek Security & Control LLC or through Nortek Security & Control
normal distribution channels. Nortek Security & Control does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer's warranty, if any.
There are no obligations or liabilities on the part of Nortek Security & Control for
consequential damages arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property, revenue, or profit, or
cost of removal, installation, or reinstallation. All implied warranties for functionality, are
valid only until the warranty expires. This Nortek Security & Control Warranty is in lieu of all
other warranties expressed or implied.
Nortek Security & Control LLC | 2GIG
5919 Sea Otter Place, Suite 100
Carlsbad, Ca. 92010
For technical support in the USA and Canada:
855‐2GIG‐TECH (855‐244‐4832)
Email:
Visit
www.nortekcontrol.com
for technical support hours of operation
For technical support outside of the USA and Canada:
Contact your regional distributor
Visit
www.dealer.2gig.com
for a list of distributors in your region
10021755A