ADEMCO LYNX Manuel de l'utilisateur - Page 11
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} ADEMCO LYNX. ADEMCO LYNX 17 pages.
Également pour ADEMCO LYNX : Manuel de démarrage rapide (8 pages), Manuel du système (14 pages)
Imprimer la page
*84 ASSIGN ZONE VOICE DESCRIPTORS
Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced when the
system annouces any event involving a zone number. Press *84 while in programming mode. NOTE: Entry of a
number other than one specified will give unpredictable results.
ASSIGN ZONE VOICE DESCRIPTORS
0 = Exit mode, upon which this prompt blinks. Press [*] + any field number to go to that field.
1 = Enter mode
ZONE NUMBER
zz
Enter the 2-digit zone number ( zz ) for which this descriptor is being assigned.
[*] = Continue to next prompt (existing descriptors will be announced, then descriptor 1 will be repeated.)
00 = Exit Zone Voice Descriptor mode (
DESCRIPTOR 1
b
vv
Enter [#] + 2-digit vocabulary index number of first descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 = accept word and advance to descriptor 2 (descriptor 2 will be announced)
8 = accept word and advance to next zone (prompt A....zz) – zone descriptor will be announced
Press any other key to repeat the selected word
DESCRIPTOR 2
vv
Enter [#] + 2-digit vocabulary index number of second descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 = accept word and advance to descriptor 3 (descriptor 3 will be announced)
8 = accept word and advance to next zone (prompt A....zz) – zone descriptor will be announced
Press any other key to repeat the selected word
DESCRIPTOR 3
d
vv
Enter [#] + 2-digit vocabulary index number of third descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 or 8 = accept word and advance to next zone (prompt A....zz) – zone descriptor will be announced
Press any other key to repeat the selected word
00
½ sec pause
F
A
14
FIRE
01
ALARM
15
FLOOR
02
ATTIC
16
FRONT
B
03
BABY
17
GARAGE
04
BACK
18
GUN
05
BASEMENT
06
BATHROOM
19
HALL
07
BEDROOM
C
20
INSIDE
08
CHECK
D
09
DEN
21
KITCHEN
10
DETECTOR
11
DINING
22
LAUNDRY
12
DOOR
23
LIBRARY
E
24
LIVING
13
EMERGENCY
*85 RECORD CUSTOM VOICE DESCRIPTORS
Use this mode to record up to 5 custom voice descriptors for use with zone announcements. Press *85 while in
programming mode. NOTE: Entry of a number other than one specified will give unpredictable results.
RECORD CUSTOM VOICE DESCRIPTORS
0 = Exit mode, upon which this prompt blinks. Press [*] + any field number to go to that field.
1 = Enter mode
CUSTOM DESCRIPTOR NUMBER
7d
Enter 7 + d + [*], where d = 0-4, each representing custom word 70, 71, 72, 73 or 74 respectively.
Existing descriptor will be announced.
Press [#] to start recorder. Start speaking immediately after the third beep.
Speak the desired word clearly near the keypad microphone. Recording stops after 1.5 seconds.
6 = Accept word and ready to record next descriptor (prompt A....7d)
[#] = Re-record descriptor
00 = Exit Record mode after pressing 6
Press any other key to repeat the recorded word.
VOCABULARY INDEX
M
25
MAIN
26
MASTER
27
MESSAGE
G
28
MOTION
O
29
OFFICE
H
P
30
PATIO
I
31
POOL
R
J
32
ROOM
K
S
33
SHED
L
34
SHOP
35
SIDE
36
SLIDING
37
SMOKE
38
STORAGE
39
SYSTEM
* +
displays blinking 84; enter
U
40
UPSTAIRS
41
UTILITY
W
42
WINDOW
Y
43
YARD
Z
44
ZONES
ST
45
1
ND
46
2
RD
47
3
70
Custom Word #1
71
Custom Word #2
72
Custom Word #3
73
Custom Word #4
74
Custom Word #5
99
Blank
(to erase previously
programmed word)
(displays blinking 85; enter * + desired data field or menu mode number)
11 –
–
desired data field or menu mode number
SYSTEM WORDS
(Announced by system
– not programmable)
AC LOSS
ARMED
AWAY
BYPASSED
CHIME
DISARMED
DISARM SYSTEM
NOW
EXIT NOW
FAULT
INSTANT
LOW BATTERY
NOT
READY TO ARM
STAY
)