ActiveAqua AAPW160 Manuel d'instruction - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} ActiveAqua AAPW160. ActiveAqua AAPW160 4 pages. Submersible pump

Imprimer la page
WARNING
• This pump is supplied with a grounding conductor and a grounding type attachment
plug. To reduce risk of electric shock, connect only to a properly grounded outlet.
• Do not remove the grounding pin from the plug.
• Do not connect to any voltage other than that shown on the pump.
• Do not pump flammable liquids.
• The national electric code requires that a grounded fault circuit interrupter (GFCI)
be used in the branch circuit supplying fountain pumps and other pond equipment.
See your electrical supplies dealer for this device.
• Do not use with water above 86°F (30°C).
• Do not allow the pump to freeze in winter, remove pump from fountains and ponds
and store in a frost-free area.
:
CAUTION
Always disconnect from electrical outlet before handling the pump.
Do not let the pump run dry.
Do not lift the pump by the power cord.
Do not pump heated liquids.
Do not operate in salt water.
PERFORMANCE
•
A clogged or dirty intake screen will greatly reduce performance. If the pump is
used on a dirty surface, raise it slightly to reduce the amount of debris contacting
the intake. If less flow is desired, adjust the flow control knob on the front of the
pump or restrict the discharge flow.
• This pump can be used submersed or in-line. Note that when used in-line it should
be placed below the water level since it is not self priming. Never run this pump
dry. If initially the pump does not work, it may be "air locked". To clear the air lock,
unplug the pump and rotate 180 degrees under water, repeat if necessary.
The included gray fitting should be attached to the inlet side of the pump only when
operated in-line. The barbed gray and black fittings use a different sized thread and
rubber O-rings. The gray in-line fitting attaches to the front of the pump and uses
the larger sized O-ring. The black fittings attach to the top of the pump and use the
smaller sized O-ring. Please use only as intended (see chart for reference).
1
ACTIVE AQUA SUBMERSIBLE PUMP COMPARISON CHART
Active Air Submersible Pump Comparison Chart
12
10
8
6
4
160
400
2
40
250
550
0
0
200
400
GALLONS PER HOUR (LPH) VOLUME
Product
Rated
Recommended Size
Item Code
GPH
(LPH)
gallons
(litres,litros)
AAPW40
43
(163)
5
(19)
AAPW160
172
(650)
15
(57)
AAPW250
291
(1,100)
25
(95)
AAPW400
370
(1,400)
40
(151)
AAPW550
529
(2,000)
55
(208)
AAPW800
793
(3,000)
80
(303)
AAPW1000
1110
(4,200)
100+
(378+)
Intake fittings are not represented in this chart.
Each aeration kit contains an extra fitting.
AAPW1000
800
600
800
1000
1200
Watts
Fitting Sizes Included
inches
(milimeters)
3
5/16"
(8mm)
9.5
1/2"
(12.7mm)
16
1/2", 3/4"
(12,7mm, 19mm)
24
1/2", 3/4"
(12.7mm, 19mm)
33
1/2", 3/4"
(12.7mm,19mm)
58
1/2", 3/4", 1"
(12.7mm,19mm, 25mm)
92
1/2", 3/4", 1"
(12.7mm,19mm, 25mm)
www.hydrofarm.com
Pump
Model
AAPW1000
AAPW800
AAPW550
AAPW400
AAPW250
AAPW160
AAPW40
6