Emerald Planet EP-RF-Li10 Manuel de l'utilisateur - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Emerald Planet EP-RF-Li10. Emerald Planet EP-RF-Li10 5 pages.

Imprimer la page

INSTALLATION POSITIONING ADVICE

When mounting an alarm on the ceiling, locate it a minimum

of 30 cm from the side wall (see Diagram 5).

• Put smoke alarms at both ends of a bedroom hallway or

large room if larger than 10m long.

• Install smoke alarms on slopped, peaked or cathedral

ceilings between 500 and 1500mm from the highest point

of the ceiling. Smoke alarms in rooms with ceiling slopes

greater than 1m in 8 m horizontally should be located on

the high side of the room (See Diagram 6).

DIAGRAM 4

MULTIPLE FLOOR PLAN

DIAGRAM 5

CEILING PLACEMENT

DIAGRAM 6

PEAK CEILING PLACEMENT

SLOPED CEILING PLACEMENT

EMERALD PLANET HEAD OFFICE - SYDNEY Unit 2 / 29 Mitchell Road, Brookvale NSW 2100 Australia P 02 9466 6000

Smoke alarm should be located

between 500mm and 1500mm

from the highest point.

WIRELESS PAIRING

WIRELESS FREQUENCY:

OPERATION CURRENT:

MAXIMUM NUMBER OF

INTERCONNECT PRODUCTS

WIRELESS DISTANCE

1: Set the ﬁrst smoke alarm to "Pair Mode"

Note: Before operation, the unit must be in normal

working mode. It is advisable to pair all alarms prior to

installation.

Press the test/hush button 3 times within 2 seconds, a red

NET LED will light for a few seconds within the alarm (if

not previously networked) or a green NET LED will light

for a few seconds within the alarm (If already networked),

then a blue NET LED is lit for 30 seconds, the smoke

alarm is now ready to pair with the next alarm.

Set next smoke alarm to "Learning Mode"

While the ﬁrst smoke alarm is in "Pair Mode" with a blue

NET LED light showing (pair within 30 seconds) Press

the test/hush button on the second smoke alarm 3 times

within 2 seconds, both green NET LED will light for 3

seconds indicating the radio link is successfully paired

Note: Products can be paired repeatedly, but all

products must be paired with the same primary smoke

alarm. Please remember this product.

To cancel pairing

If you want to cancel network pairing:

Ensure the power is be disconnected by turning the

mounting plate anti-clockwise until it unlocks.

Press the test/hush button and hold down (do not release),

and at the same time reconnect power by twisting the

mounting plate clockwise until it locks into place.

The red LED will light for 3 seconds, then release the test

button when the red LED light switches off.

When the button is released, the red LED will light for 3

seconds. In these 3 seconds, press the button to clear all

paired alarms, the red LED will ﬂash for a while. When the

red LED stops ﬂashing, the network is successfully cleared.

Radio link test

To ensure that all the products have been successfully paired;

Select one device, press and hold the button for about 2

seconds until the smoke alarm enters "Test alarm mode"

and then release the button, the device will automatically

send "Radio link test" information.

After short delay, all other paired alarms will enter "Radio

link test" status (red LED flash twice every second for 5

minutes, beep twice every second for 10 seconds). If

an alarm does not start flashing red, then network pairing

has failed or the distance between the connected alarms is

too great (the connected devices cannot reach each other).

Note: In "Radio link test" status device, press the

button and the device immediately enter the normal

standby mode.

Note: Before installing, place the product in each

installed room and select the device in the farthest room

for this test, to ensure that other products successfully

enter the "Radio link test" status.

433MHz

RF Receiver: <6mA

RF emitter: <30mA

30PCS

> 20 meters

Note: Make sure the batteries are

installed correctly before

operating the product.