AFG 2.0AS Assembly and Manuel d'assemblage et d'utilisation - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel d'assemblage et d'utilisation pour {nom_de_la_catégorie} AFG 2.0AS Assembly and. AFG 2.0AS Assembly and 15 pages. Afg series
Également pour AFG 2.0AS Assembly and : Manuel d'assemblage et d'utilisation (16 pages)
Imprimer la page
AS SE MB LY ST EP
HARDWARE BAG CONTENTS :
FLAT WASHER (C)
Qty: 12
BOLT (M)
65 mm
Qty: 2
SEAT HEAD PAD
FLAT WASHER (C)
SEAT BACK ADJUSTMENT BAR
SEAT BACK PAD
SEAT BOTTOM PAD
NYLON
NUT (E)
FLAT
WASHER (C)
SEAT BOTTOM
ADJUSTMENT BAR
BOLT (M)
A
Open HARDWARE BAG .
B
Attach SEAT HEAD PAD to CENTER
SUPPORT FRAME using 4 BOLTS (F) and 4 FLAT WASHERS (C), as shown in diagram.
C
Install SEAT BACK ADjUSTMENT PIN in CENTER SUPPORT FRAME. (Fully thread into
CENTER SUPPORT FRAME after SEAT BACK ADjUSTMENT BAR is installed.)
D
Attach SEAT BACK PAD to SEAT BACK ADjUSTMENT BAR using 4 BOLTS (F) and 4 FLAT
WASHERS (C), and insert into CENTER SUPPORT FRAME as shown in diagram.
E
Attach SEAT BOTTOM PAD to SEAT BOTTOM ADjUSTMENT BAR using 2 BOLTS (M) and 4
FLAT WASHERS (C) and 2 NYLON NUTS (E), and insert into SEAT WELDMENT as shown in
diagram.
F
Install FOAM ROLLERS onto LEG ROLLER SUPPORT TUBE using 2 BOLTS (F), 2 LOCK
WASHERS (L) and 2 CHROME WASHERS (U), as shown in diagram.
G
Attach WATER BOTTLE HOLDER to CENTER SUPPORT FRAME using 2 BOLTS (N).
10
H
Tighten all hardware in Step 4.
2.0AS_Rev.1.5.indd 10-11
NYLON
BOLT (F)
LOCK WASHER (L)
NUT (E)
25 mm
Qty: 2
Qty: 2
Qty: 10
BOLT (N)
CHROME WASHER (U)
25 mm
Qty: 2
Qty: 2
BOLT (F)
BOLT (N)
FLAT WASHER (C)
CENTER SUPPORT
FRAME
BOLT (F)
SEAT BACK
ADJUSTMENT PIN
LEG ROLLER
CHROME WASHER (U)
LOCK WASHER (L)
LEG ROLLER
BOLT (F)
SUPPORT TUBE
ASSEMBLY STEP (1 0 lbs. Wei ght Stack)
HARDWARE BAG CONTENTS :
FLAT WASHER (C)
Qty: 8
A
Open HARDWARE BAG .
B
Attach LOWER MOUNTING BRACKET (after
removing pre-installed guide rod bolts) to BASE
WATER
FRAME in desired location, using 2 BOLTS (P),
BOTTLE
4 FLAT WASHERS (C) and 2 NYLON NUTS (E).
HOLDER
NOTE: Refer to page 25 for mounting positions.
C
Position each GUIDE ROD so that the mounting
holes are in the upper position, and insert
GUIDE RODS into corresponding sleeves in
LOWER MOUNTING BRACKET.
D
Slide 1 UPGRADE SPACER and then slide 1
RUBBER BUMPER onto each guide rod, as
shown in diagram.
E
Install each WEIGHT PLATE onto guide rod as
shown in diagram. Ensure than the weight pin
selector slot is positioned downward and in
same direction.
F
Install BAYONET onto GUIDE RODS as shown in
diagram.
G
Re-install GUIDE ROD bolts into LOWER
MOUNTING BRACKET.
H
Install UPPER MOUNTING BRACKET to top of
GUIDE RODS, as shown in diagram, using 2
BOLTS (Q), 4 FLAT WASHERS (I) and 2 NYLON
NUTS (K).
I
Attach UPPER MOUNTING BRACKET to UPPER PULLEY ASSEMBLY using 2 BOLTS (O), 4
FLAT WASHERS (C), and 2 NYLON NUTS (E).
NOTE: Ensure that the UPPER MOUNTING BRACKET's position corresponds to the position
of the LOWER MOUNTING BRACKET before securing it to the UPPER PULLEY ASSEMBLY.
j
Tighten all hardware.
FLAT WASHER (I)
NYLON
NYLON
Qty: 4
NUT (E)
NUT (K)
Qty: 4
Qty: 2
BOLT (O)
BOLT (P)
100 mm
70 mm
Qty: 2
Qty: 2
UPPER MOUNTING BRACKET
FLAT WASHER (I)
NYLON NUT (K)
BOLT (O)
UPPER
PULLEY
ASSEMBLY
FLAT
WASHER (C)
NYLON NUT (E)
RUBBER
BUMPER
BOLT (P)
LOWER MOUNTING
FLAT WASHER (C)
BASE FRAME
NYLON NUT (E)
RUBBER
BUMPER
Qty: 2
BOLT (Q)
40 mm
Qty: 2
BOLT (Q)
FLAT
WASHER (I)
GUIDE
ROD
BAYONET
WEIGHT
PLATES
UPGRADE
SPACER
BRACKET
11
9/23/08 10:14:31 AM