AutomationDirect Stellar SR55 Manuel de démarrage rapide - Page 11

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} AutomationDirect Stellar SR55. AutomationDirect Stellar SR55 20 pages.

AutomationDirect Stellar SR55 Manuel de démarrage rapide
Wiring Connection (continued)
3-Wire Control Diagram
110/230Vac control supply (U s )
and digital input (U c ) programming
Emergency Stop
!
110/230Vac
L
N
N
refer
to
wIrIng DIagrams are specIfIcally where the control supply Voltage
to the control cIrcuIt Voltage
confIguratIons must also be In accorDance wIth exIstIng local anD natIonal coDes anD
regulatIons
référer
schémas De câblage sont recommanDées spécIfIquement lorsque la tensIon D
De commanDe
DoIVent pas être alImentés séparément
également être en conformIté aVec les coDes et les règlements locaux et natIonaux en
.
VIgueur
p
ower factor correctIon capacItors
anD the motor
l
es conDensateurs D
entre le Démarreur progressIf et le moteur
enDommager les thyrIstors
110/230Vac (U s ) and (U c ) user
programmable control diagram
Emergency Stop
110/230Vac
!
Stop
Start
K2
N
User programmable inputs
are fully programmable
D1-1I = High Start / Low Stop
D1-2I = None
D2-1I = High Reset
* Note: Power factor correction capacitors (PFCs)
in some cases can reduce a facility's kVAR charges.
need for, and location of, PFCs should be performed by a qualified
engineer (from your utility company or a power quality engineering
firm).
1st Ed., Rev.E – 02/02/2017 – Stellar
D1-1I
D1-2I
D2-1I
33
D1COM
D2COM
34
K1
table 1
9
on page
for Input control Voltages
(u
.
tableu 1
au
à la page
(u
)
est IDentIque à la tensIon Du cIrcuIt De commanDe
s
,
or there Is a rIsk of DamagIng the thyrIstors Due to current peaks
'
amélIoratIon Du facteur DepuIssance ne DoIVent pas être montés
.
K2.2
1)
L
D1-1I
D2-1I
K2.1
D1COM
D2COM
N
1) Optional high reset. If this reset is required, ensure "User
Programmable" is selected in the control method menu found
in the Digital Inputs menu. If you would prefer the reset to
work by removing and reapplying the Start Signal on D1-1I
then select "Two wire control" in the control method menu.
PFCs cannot be located between the SR55 and the motor.
®
SR55 Soft Starter Quick-Start Guide
SR55 Quick-Start Guide
3-Wire Control Diagram
24Vdc control supply (U s ) and
digital input (U c ) programming
(only applicable for SR55-017 to SR55-361)
Emergency Stop
!
24Vdc
24
D1-1I
D1-2I
VDC
0VDC
D1COM
D2COM
0Vdc
),
anD not to be supplIeD separately
c
9
pour Des tensIons De contrôle D
. t
outes les confIguratIons De câblage DoIVent
*
must not be posItIoneD between the soft starter
,
parce que les poIntes De courant rIsquent à
24Vdc (U s ) and (U c ) user programmable control
diagram (only applicable for SR55-017 to SR55-361)
Emergency Stop
24Vdc
!
Stop
33
Start
34
K2
K1
0Vdc
Digital Input
Programming
D1-1I = Start
D1-2I = Stop
D2-1I = Reset
D2-1I
33
34
K1
. t
hese recommenDeD
(u
)
Is IDentIcal
s
. o
ther wIrIng
'
. c
entrée
es
'
alImentatIon
(u
). u
s et
c
K2.2
24
D1-1I
D2-1I
VDC
K2.1
0VDC
D1COM
D2COM
Determining the
u
c ne
.
1)
33
34
K1
11