Dynamic NXT MultiFit Manuel d'instruction - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Dynamic NXT MultiFit. Dynamic NXT MultiFit 8 pages. Head support

Imprimer la page
Latch Clamp
Step /
Étape
#3
Head Support Pad /
(Figure 3)
Unzip the back of the pad cover exposing the inside
Locking
of the pad. Set the ball on the head support into the
Step 3 – Head Pad
Collar
receiver inside the back of
the pad. Secure using the 3 screws provided (Figure
Unzip the back of the pad cover exposing the inside of the
4). The pad can then be bent in or out
pad. Set the ball on the head support into the received
to customize the fit for the user.
inside the back of the pad. Secure using the 3 screws
provided (see Figure 4). The head pad can then be bent in
Décompressez l'arrière de la housse de protection
Latch Clamp
or out to customize the fit to the user's head.
en exposant l'intérieur du coussin. Placez la balle sur
le support de tête dans le récepteur à l'arrière du
(Figure 3)
coussin. Fixez en utilisant les 3 vis fournies (Figure
OPTIONAL STEP – Install Flip Back Hardware (if ordered)
4). Le coussin peut ensuite être plié ou déplié pour
personnaliser l'ajustement pour l'utilisateur.
To install the optional flip back hardware, first remove the
head support arm by unfastening the hardware (3 pieces)
that secures it (see Figure 5). Set the hardware and head
support arm aside to reattach after the flip back has been
installed.
Optional Step /
Install Flip Back Hardware
Installez le matériel rabattable
To install the optional flip back hardware, first
remove the head support arm by unfastening
the hardware (3 pieces) that secures it (Figure
5). Set the hardware and head support arm
aside to reattach after the flip back has been
installed.
Pour installer le matériel rabattable optionnel,
Latch Clamp
retirez d'abord le bras de support de tête en
Thin Washer
détachant le matériel (3 pièces) qui le fixe
Heavy Duty Washer
Post Extension
(Figure 5). Réglez le matériel et le bras de
(Figure 6)
support de tête de côté pour les remettre en
place après que le rabat arrière a été installé.
Latch Clamp
Thin Washer
Heavy Duty Washer
(Figure 6)
4
collar down to the top of the mounting kit. Secure in place
by tightening its screw against the head support vertical
post. This will ensure that the height of the head support
Next, slide the Head Support's vertical post through the
will always return to same height that it is set to.
Coussin de support de tête
mounting bracket and secure in place using the latch clamp
(see Figure 3). The channel in the vertical post should slide
over the Channel Screw (illustrated in Figure 2), ensuring
the post cannot rotate after installation.
Set the post to the desired height, and slide the locking
collar down to the top of the mounting kit. Secure in place
by tightening its screw against the head support vertical
post. This will ensure that the height of the head support
will always return to same height that it is set to.
Étape facultative
(if ordered)
Flip Back
(si commandé)
Post Extension
Special Nut
Flip Back
Special Nut
Next, install the flip back post extension over
the existing post. With the hardware
provided with, secure the flip back extension
by inserting the latch clamp through the
channel (with thin washer and heavy duty
washer) and tightening the special nut on the
Note: both the heavy duty washer and the special
nut must be installed with the small two sided
protrusion going into the elongated holes on each
Next, install the flip back post extension over
the existing post. With the hardware
provided with, secure the flip back extension
by inserting the latch clamp through the
channel (with thin washer and heavy duty
washer) and tightening the special nut on the
Note: both the heavy duty washer and the special
nut must be installed with the small two sided
protrusion going into the elongated holes on each
side of the flip back post extension
Screws used to secure
Pad to Head Support
Vis utilisées pour fixer le
Screws used to secure
coussin au support de tête
Pad to Head Support
(Figure 4)
(FIGURE 4)
(Figure 4)
Screws used to secure
Pad to Head Support
(Figure 4)
(Figure 4)
(Figure 5)
Support Arm
Hardware
Hardware
(Figure 5)
(FIGURE 5)
side of the flip back post extension
other side.
Support Arm
Hardware
Support Arm
Bras de support
other side.
Matériel