Automationdirect.com AcuAMP ACTR Series Instructions d'installation

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} Automationdirect.com AcuAMP ACTR Series. Automationdirect.com AcuAMP ACTR Series 2 pages.

Imprimer la page

Specifications

24VDC nominal, (12-32VDC)

Power Supply

Intended for use with a Class 2 source with the

secondary fused to limit power to a maximum

of 100 VA

Output Signal

4-20 mA, Loop Powered

Output Limit

23mA

Output Impedance

< 600Ω @ 24VDC

Accuracy

1.0% FS, 10 to 100% of range

ACT: 50/60Hz, Average Responding

Frequency Range

ACTR: 20-400Hz, True RMS

Isolation Voltage

UL tested to 2200VAC

Response Time

600ms (90% step change)

Case

UL 94V-0 Flammability rated thermoplastic

2.22 X 1.19 in (56.3 X 30.2 mm)

Sensing Aperture

ACT1200:

3.44 x 2.31 in (87.3 x 58.8 mm)

-Temp -4 to 122°F (-20 to 50°C)

-Humidity 0-95% RH, Non-condensing

Environmental

-Pollution degree 2

-Altitude 2000 meters

UL/cUL File E197592

Certifications

Sensed Current Limit

Range

Continuous 6 Seconds

All

1600A

1920A

For products intended for the EU market, the

following is applicable to the CE compliance of

the product:

The ACT/ACTR Series may comply with EN 61010-1 CAT III

300V max line-to-neutral measurement category. If insulated

cable is used for the primary circuit, the voltage rating of the

measurement category can be improved according to the

characteristics given by the cable manufacturer.

ACT 400 - 42L - S

ACT: AC current transducer, average responding

ACTR: AC current transducer, True RMS

Warning! Risk of hazardous voltage

When operating the transducer, certain parts

may carry hazardous live voltage (e.g., primary

conductor, secondary terminals). The transducer

should not be put into service if the installation is

not complete.

Warning! Risk of electric shock or

personal injury

1 Second

Safe operation can only be guaranteed if the

transducer is used for the purpose for which it was

6400A

designed and within the limits of the technical

specifications. When this symbol is used, it

means you should consult all documentation to

understand the nature of potential hazards and

the action required to avoid them.

3505 Hutchinson Road, Cumming, GA 30040

Phone: (800) 633-0405 or (770) 889-2858

Part Number Key

CASE STYLE

S - Split Core

OUTPUT

42L - 4-20mA, loop powered

RANGE

400 A

600 A

800 A

1200 A

AutomationDirect.com (ADC)

ACT/ACTR - Inst - Rev 1

0820

P-N 292000109

ACT/ACTR

SERIES

INSTALLATION

INSTRUCTIONS

Quick Start Guide

Remove top section of sensing ring off by

carefully prying clips away and lifting the

section vertically.

2. Mount the sensor to a DIN rail or surface

using screws in corners, if needed.

3. Place conductor inside ring and replace top

section until the clips snap firmly closed.

4. Connect output wiring.

a. Use No. 22 to 14 AWG copper wires rated

min. 75C and tighten terminals to 5-7 in-lbs.

b. Ensure output load does not exceed

product specifications.

c. Connect 24 VDC power supply and load

in series. Observe polarity.

5. Verify that the display or controller is

reading the output correctly (4mA)

6. Energize the monitored circuit.