Kinyo D-655 Manuel - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Kinyo D-655. Kinyo D-655 5 pages. 5.1ch home theater speaker system

Imprimer la page

Note:

Pro logic function is available only for selected input sources such as Dolby 2/0. PCM or

Analog. Please check the signal type.

SPEAKER SETUP:

Switch to or from the big or small speaker, it will enhance bass effect when in small speaker mode.

a SPEAKER SETUP LED:

When light is on. Dolby small speaker is on.

6.LISTENING MODE :

Press it then you may select the listening mode ( Maximum, standard, or late night)

a. LISTENING MODE LED:

Press the listening mode key, the flashing LED means you can now select different modes.

(Maximum, standard, or late night)

Press LISTENING MODE key and then adjust A and ▼ key to select the mode you prefer

At this time, the OPTICAL. COAXIAL and ANALOG LED will have different indications and will show

you what mode you have selected. ( See table below )

LISTENING

MODE LED

OPTICAL LED

COAXAL LED

ANALOG LED

LISTENING

MODE

FLASH

LIGHT UP

MAXIMUM

FLASH

LIGHT UP

STANDARD

FLASH

LIGHT UP

LATE NIGHT

Press LISTENING MODE again to exit setup.

DELAY TIME :

Press this cycle key to adjust" Center Adjustment " — " Surround Adjustment"-"Quit this function"

a. CENTER DELAY TIME :

Press the Delay Time key for the first time and the " LISTENING MODE "&"DELAY TIME" LED's will

flash. Now you can adjust the delay time for the Center channel by using the A and T buttons.

When adjusting, the OPTICAL. COAXIAL, ANALOG. DOLBY DIGITAL and PRO LOGIC / STEREO

LED's are used to indicate the delay time you have selected (See table below)

b. SURROUND DELAY TIME:

Press the Delay Time key for the first the time and the" TEST / ADJUST & " DELAY TIME "LED's will

flash. Now you can adjust the delay time for Surround channel by using the A and T button. When

adjusting, the OPTICAL. COAXIAL. ANALOG. DOLBY DIGITAL and PRO LOGIC / STEREO LED's

are used to indicate the delay time you have selected ( See table blow )

LISTENING

modi:

DELAY

TIME LED

OPTICAL

i ED

COAXIAL

i BD

ANALOG

LED

SURROl \D

DEI AY

FLASH

OmS

FLASH

LIGHT UP

5mS

FLASH

LIGHT UP

lOmS

FLASH

LIGHT UP

15mS

Press DELAY TIME again to exit this function

8. TEST / ADJUST:

Press it and the decoder will send a signal to check each channel one at a time (Channel FL. CEN,

FR. RR. RL. SUB) Then you may start to adjust the volume level of each channel starling from " FL"

channel. If you want to skip TEST function during this cycle, press TEST / ADJUST again It will skip

the cycle test and allow you to adjust the volume level of each channel from the first channel "FL".

You may also press MUTE any time to quit the adjust function,

a. The "FL" speaker will emit a test sound and then you can adjust the volume level by the A and ▼

keys. If you don't make any adjustments within 8 seconds, it will quit this mode automatically

b. Press TEST/ADJUST again to adjust volume level for CEN channel. The "CEN" speaker will emit

a test sound and then you can adjust the volume level by the A and T keys.

If you don't make any adjustments within 8 seconds, it will quit this mode automatically.

C. Press TEST/ADJUST again to adjust volume level for FR channel. The " FR " speaker emits test

sound and then you can adjust the volume level by adjusting A and ▼ keys.

If you don't do any action in 8 seconds, it will quit this adjust mode automatically

d. Press TEST/ADJUST again to adjust volume level for RR channel. The " RR " speaker emits test

sound and then you can adjust the volume level by adjusting A and ▼ keys.

If you don't make any adjustments within 8 seconds, it will quit this adjust mode automatically.

e. Press TEST/ADJUST again to adjust volume level for RL channel. The " RL " speaker emits test

sound and then you can adjust the volume level by adjusting A and ▼ keys.

If you don't make any adjustments within 8 seconds, it will quit this adjust mode automatically.

f. Press TEST/ ADJUST again to adjust volume level for SUB channel. The" SUB " speaker emits

sound and then you can adjust the volume level by adjusting A and ▼ keys.

If you don't make any adjustments within 8 seconds, it will quit this mode automatically.

g. Press TEST/ADJUST again to quit this function.

TEST/ ADJUST LED:

When LED is flashing, you can adjust the volume level of each channel.

♦ Press TEST/ADJUST. When LED is flashing, you can adjust the volume level of each channel

( BALANCE ) by pressing the A and ▼ keys.

♦ OPTICAL. COAXIAL. ANALOG. DOLBY DIGITAL and PRO LOGIC. SPEAKE R MODE all have

different LED indicators. When lit they will indicate what volume level you adjusted. (See table blow)