Gakken Stirling engine Instructions d'assemblage et d'utilisation - Page 5

Parcourez en ligne ou téléchargez le pdf Instructions d'assemblage et d'utilisation pour {nom_de_la_catégorie} Gakken Stirling engine. Gakken Stirling engine 12 pages.

Imprimer la page
5
Figure ー
5
Attach the rear wheels to the body.
Overturn the B1 body and
attach the rear wheels
4
assembled at Figure ー   
with the B6 rear wheel
holders. Attach the 18mm
screw for the front wheels too.
Full-scale
※Check the size with this.
screw (6mm) screw (18mm)
bush (7mm)
spring (9mm)
washer
washer
(7mm in diameter)
(8mm in diameter)
nut
the hinder
(large 6mm)
part
6
Figure ー
screw (6mm)
Attach the front wheels assembled at
4
Figure ー    in the following order.
6
Attach the front wheels
washer (7mm in diameter)
bush (7mm)
to the body.
front wheel holder
washer (8mm in diameter)
spring (9mm)
washer (7mm in diameter)
nut (large 6mm)
cross section of the body
and the front wheels
spring
nut (large 6mm)
(9mm)
washers
(7mm in diameter)
B5
bush
(7mm)
the hinder part
screw
washers
B1
(18mm)
(8mm in diameter)
3

Attaching the Cylinder to the Body

PARTS
Parts to be used
C
※ There may be more screws, washers, nuts
  and bushes than actually used for spare.  
C1
C3
cylinder
sliding base
C4
cylinder holder
C2
Two
cylinder supports
B6
rear wheel holders
B3
rear wheel
the fore part
screw (18mm)
B1
body
nut (large 6mm)
washer
screw (6mm)
(7mm in diameter)
spring (9mm)
washer
(8mm in diameter)
B2
front wheels
bush (7mm)
washer (7mm in diameter)
the fore part
screw (18mm)
B1
body
C6
Four
Two 26mm
cylinder springs
screws
C5
15.5mm spring
Four 6mm
screws
※Check the length of screws
 with these diagrams.
8
7
Figure ー
Overturn the body up
and attach the C3
sliding base to the
front wheels side
with the C5 spring.
Full-scale
※Check the size with this.
C5
spring (15.5mm)
8
Figure ー
Fasten C2 cylinder
supports to the B1
body with 6mm
screws.
9
Figure ー
Attach the C1
cylinder using the C6
cylinder springs.
Be sure to fasten the
C4 cylinder holder at
the back part with
30mm screws.
Full-scale
※Check the size with this.
screw (6mm)
screw (26mm)
screw (30mm)
Two 30mm
screws
C6
 cylinder spring
spring retaining bush
(6mm in diameter)
2.5mm in thickness
spring (13mm)
Warning ★ Fire is used for the experiment. Use great caution to avoid
a burn and fire. Do not let a 15 or less-year-old child experiment alone.
7
Attach the C3 sliding base.
C5
spring (15.5mm)
C3
sliding base
the fore part
B1
8
Attach the C2 cylinder supports.
C2
cylinder support
screw (6mm)
screw (6mm)
screw (6mm)
screw (6mm)
C2
cylinder support
the fore part
9
Attach the C1
screw (30mm)
cylinder.
screw (30mm)
screw (26mm)
C4
※Fasten the cylinder so
 that it becomes parallel
 to the body.
C6
cylinder spring
the fore part
B1
C2
cylinder support
9
the hinder part
body
※When tightening the screws,
 tighten four of them equally.
the hinder part
B1
body
When the C1
cylinder comes
apart, set the
parts like this.
cylinder holder
C6
C1
cylinder
spring
(13mm)
C6
the hinder part
body