Autonics BD-A1 Manuel du produit
Parcourez en ligne ou téléchargez le pdf Manuel du produit pour {nom_de_la_catégorie} Autonics BD-A1. Autonics BD-A1 3 pages. Laser displacement sensors amplifier unit
Également pour Autonics BD-A1 : Manuel (14 pages)
Imprimer la page
TCD220048AB
Laser Displacement Sensors
: Amplifier unit
BD Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc are subject to change without notice for product
improvement Some models may be discontinued without notice.
Features
• Reference distance :30/65/100/300/600 mm
• Easy maintenance with detachable sensor head/amplifier unit
• Maximum resolution: 1 ㎛ (vary by model)
• Accurate measurement with minimal influence from target color or material
• Interconnection of up to 8 sensor amplifier units
: Mutual interference prevention function and auto channel sorting
• Various calculation functions supported (addition, subtraction, average)
• Various filter functions for stable measurement (movement average, differential,
median)
• Auto sensitivity adjustment (1-point, 2-point teaching)
• Dedicated software provided (atDisplacement)
• DIN rail and wall mount support (bracket accessory required for wall mount)
• Sensor head: IP67 protection structure
※ Sensor head model BD-300/600 supports only over 5.0 firmware version of the
amplifier unit (BD-A1).
ᜢ ᜧ ᜫ
Safety Considerations
• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.
• symbol indicates caution due to special circumstances in which hazards may occur.
Warning
Failure to follow instructions may result in serious injury or death
01. Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss.(e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
high humidity, direct sunlight, radiant heat, vibration, impact or salinity
may be present.
Failure to follow this instruction may result in explosion or fire.
03. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire.
05. Check 'Connections' before wiring. [Amplifier unit]
Failure to follow this instruction may result in fire.
Caution
Failure to follow instructions may result in injury or product damage
01. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage.
02. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire.
Cautions during Use
• Follow instructions in 'Cautions during Use' . Otherwise, it may cause unexpected
accidents.
• The power supply should be insulated and limited voltage/current or Class 2, SELV
power supply device.
• Do not install where strong magnetic or electric field exist. Otherwise, the resolution
may be adversely affected.
• Mutual optical interference between laser sensors and photoelectric sensors may
result in malfunction.
• Mutual optical interference between laser sensors may result in malfunction.
• When connecting DC relay or other inductive load to the output, remove surge by
using diode or varistor.
• Wire as short as possible and keep away from high voltage lines or power lines, to
prevent surge and inductive noise.
• For the optimized performance, it is recommended to measure after 30 minute from
supplying power.
• When detecting with the maximum sensitivity, an error may occur depending on each
characteristic deviation.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in 'Specifications')
- Altitude max. 2,000 m
- Pollution degree 2
- Installation category II