Dynamite Passport UltraDuo DYN4300 Manuel d'instruction - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Dynamite Passport UltraDuo DYN4300. Dynamite Passport UltraDuo DYN4300 4 pages.
Imprimer la page
17
LI-PO fAST CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
LiPo FAST CHG
to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog dial to go into
this menu.
4.0A
7.4V(2S)
Rotate the Jog dial to go to the LiPo FAST CHG screen and set charging param-
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B)
is dependent on the number of cells in series. For example, with Li-Po batteries
A
these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
To select values other than the existing parameters:
Near the end of a standard charging cycle, the charger switches from Constant
• Press the Jog dial so the charge current value (A) flashes
Current (CC) mode to Constant Voltage (CV) mode to slowly "top off" the current in
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
the battery as close as possible to the maximum capacity.
• Press the Jog dial to save the value and the voltage value (B) flashes
In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
time; however, the final capacity of the battery will be less than what you would get
series (C))
using the standard charge method.
• Press the Jog dial again to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another
program such as CHARGE, BALANCE, STORAGE or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
18
LI-PO STORAGE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select values other than the existing parameters:
to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog dial to go into
• Press the Jog dial so the charge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the LiPo STORAGE screen and set charging param-
• Press the Jog dial to save the value and the voltage value (B) flashes
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B)
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
is dependent on the number of cells in series. For example, with Li-Po batteries
series (C))
these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
• Press the Jog dial to save the voltage value
If you don't plan on using your battery for a long time, it is best to charge (or
If no parameters are flashing, you can rotate the Jog dial to select another
discharge) the battery to its optimal storage voltage and capacity.
program such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
LiPo STORAGE
2.5A
11.1V(3S)
A
B
C
19
LI-PO dISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select values other than the existing parameters:
to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog dial to go into
• Press Jog dial so the discharge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the discharge current value
Rotate the Jog dial to go to the LiPo DISCHARGE screen and set discharging
• Press the Jog dial to save the value and the voltage value (B) flashes
parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Volt-
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
age (B) is dependent on the number of cells in series. For example, with Li-Po bat-
series (C))
teries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
• Press Jog dial to save the voltage value
A battery's capacity can be verified by discharging it to its minimum voltage level
If no parameters are flashing, you can rotate the Jog dial to select another
and measuring the current as the battery is discharged.
program such as CHARGE, BALANCE, FAST CHG or STORAGE.
To start discharging, press and hold the Jog dial for 3 seconds.
LiPo DISCHARGE
2.0A
22.2V(6S)
A
B
C
20
NI-MH BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
During charging, the Jog dial can be rotated counterclockwise to show several
to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog dial to select
parameter messages on the LCD screen, including: Ni-MH Sensitivity, Input Power
NiMH.
Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status
and Capacity Cutoff. The charger signals when the charging (or discharging)
Rotate the Jog dial to go to one of the control screens (CHARGE, Auto CHARGE,
process is complete (if Buzzer is set to ON).
DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs.
CAUTION: The Ni-MH program menus are to be used ONLY for the
Correctly connect your Ni-MH battery to the charger. Press the Jog dial and adjust
charging and discharging of Ni-MH battery packs. The charging of other
the charging parameters as needed. Press and hold the Jog dial (approximately 3
seconds) until the screen changes to start the battery check/charge sequence.
battery types using these programs will result in damage to the battery
or charger.
After confirmation, charging starts and information will show on the LCD screen
CAUTION: Using a charge rate that is not compatible with the battery
(information may vary).
capacities may result in damage or malfunction of the charger or
B
C
A. A Ni-MH battery pack is
batteries.
charging
NiMH 2.0A 7.59V
A
B. Charging rate is 2.0A
01082
CHG 022:43
(2000mAh)
E
d
C. Voltage being applied to the battery is currently 7.59V
d. Present charge level of the battery is 1082 mAh
E. Time elapsed since the charge process started is 22:43
21
NI-MH CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog dial to go into
• Press the Jog dial so the charge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the NiMH CHARGE screen and set charging param-
• Press the Jog dial to save the value
eters. The charging amperage (A) can be set between 0.1 and 10.0A.
If no parameters are flashing, you can rotate the Jog dial to select another
program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE.
NiMH CHARGE
To start charging, press and hold the Jog dial for 3 seconds.
CURRENT
1.0A
A
22
NI-MH AUTO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog dial to go into
• Press the Jog dial so the charge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the NiMH Auto CHARGE screen and set charging
• Press the Jog dial to save the value
parameters. The charging amperage (A) can be set between 0.1 and 10.0A.
If no parameters are flashing, you can rotate the Jog dial to select another
program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE.
NiMH Auto CHARGE
To start charging, press and hold the Jog dial for 3 seconds.
CURRENT
1.0A
A
23
NI-MH dISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog dial to go into
• Press the Jog dial so the discharge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the discharge current value
Rotate the Jog dial to go to the NiMH DISCHARGE screen and set discharging
• Press the Jog dial to save the value and the cutoff voltage value (B) flashes
parameters. The discharging amperage (A) can be set between 0.1 and 5.0A.
• Rotate the Jog dial to INCREASE OR DECREASE the cutoff voltage
• Press the Jog dial to save the voltage value
A battery's capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
If no parameters are flashing, you can rotate the Jog dial to select another
set from 0.1 to 25.2V.
program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE.
To start discharging, press and hold the Jog dial for 3 seconds
NiMH DISCHARGE
0.1A
CUT: 1.0V
A
B
24
NI-MH RE-PEAK CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog dial to go into
• Press the Jog dial so the re-peak value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the value
Rotate the Jog dial to go to the NiMH RE-PEAK screen and set re-peak param-
• Press the Jog dial to save the value
eters to a value of between 1 and 3.
If no parameters are flashing, you can rotate the Jog dial to select another
B
C
program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE.
NiMH RE-PEAK
Press the Jog dial to go to the next menu.
1
25
NI-MH CyCLE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select values other than the existing parameter:
to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog dial to go into
• Press the Jog dial so the cycle type (A) flashes
this menu.
• Rotate the Jog dial to set the cycle type as CHG>DCHG or DCHG>CHG
Rotate the Jog dial to go to the NiMH CYCLE screen and set charge/discharge
• Press the Jog dial to save your choice and the number of cycles (B) flashes
cycle count parameters.
• Rotate the Jog dial to set the cycle count between 1 to 5
• Press the Jog dial to save the cycle count value
The battery can be put through a series of charge/discharge cycles using this
If no parameters are flashing, you can rotate the Jog dial to select another
program. Cycling Ni-MH batteries can increase capacity and rejuvenate neglected
batteries. Discharge capacity and average battery voltage help you compare batter-
program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK.
ies for the best run time and power.
To start cycling, press and hold the Jog dial for 3 seconds.
NiMH CYCLE
CHG>DCHG
5
A
B
26
NI-Cd BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
During charging, the Jog dial can be rotated counterclockwise to show several
to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog dial to select
parameter messages on the LCD screen, including: Ni-Cd Sensitivity, Input Power
NiCd.
Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status
and Capacity Cutoff. The charger signals when the charging (or discharging)
Rotate the Jog dial to go to one of the control screens (CHARGE, Auto CHARGE,
process is complete (if Buzzer is set to ON).
DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs.
Correctly connect your Ni-Cd battery to the charger. Press the Jog dial and adjust
the charging parameters as needed. Press and hold the Jog dial (approximately 3
seconds) until the screen changes to start the battery check/charge sequence.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).
B
C
A. A Ni-Cd battery pack is
NiCd 2.0A 7.59V
charging
A
B. Charging rate is 2.0A
CHG 022:43
01082
(2000mAh)
E
d
C. Voltage being applied to the battery is currently 7.59V
d. Present charge level of the battery is 1082 mAh
E. Time elapsed since the charge process started is 22:43
27
NI-Cd CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog dial to go into
• Press the Jog dial so the charge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the NiCd CHARGE screen and set charging param-
• Press the Jog dial to save the value
eters. The charging amperage (A) can be set between 0.1 and 10.0A.
If no parameters are flashing, you can rotate the Jog dial to select another
program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE.
NiCd CHARGE
To start charging, press and hold the Jog dial for 3 seconds.
CURRENT
1.0A
A
28
NI-Cd AUTO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog dial to go into
• Press the Jog dial so the charge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the NiCd Auto CHARGE screen and set charging
• Press the Jog dial to save the value
parameters. The charging amperage (A) can be set between 0.1 and 10.0A.
If no parameters are flashing, you can rotate the Jog dial to select another
program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE.
NiCd Auto CHARGE
To start charging, press and hold the Jog dial for 3 seconds.
CURRENT
1.0A
A
29
NI-Cd dISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog dial to go into
• Press the Jog dial so the discharge current value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the discharge current value
Rotate the Jog dial to go to the NiCd DISCHARGE screen and set discharging
• Press the Jog dial to save the value and the cutoff voltage value (B) flashes
parameters. The discharging amperage (A) can be set between 0.1 and 5.0A.
• Rotate the Jog dial to INCREASE OR DECREASE the cutoff voltage
• Press the Jog dial to save the voltage value
A battery's capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
If no parameters are flashing, you can rotate the Jog dial to select another
set from 0.1 to 25.2V.
program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE.
To start discharging, press and hold the Jog dial for 3 seconds
NiCd DISCHARGE
0.1A
CUT: 1.0V
A
B
30
NI-Cd RE-PEAK CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select a value other than the existing parameter:
to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog dial to go into
• Press the Jog dial so the re-peak value (A) flashes
this menu.
• Rotate the Jog dial to INCREASE OR DECREASE the value
Rotate the Jog dial to go to the NiCd RE-PEAK screen and set re-peak parameters
• Press the Jog dial to save the value
to a value of between 1 and 3.
If no parameters are flashing, you can rotate the Jog dial to select another
program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE.
NiCd RE-PEAK
Press the Jog dial to go to the next menu.
1
31
NI-Cd CyCLE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
To select values other than the existing parameter:
to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog dial to go into
• Press the Jog dial so the cycle type (A) flashes
this menu.
• Rotate the Jog dial to set the cycle type as CHG>DCHG or DCHG>CHG
Rotate the Jog dial to go to the NiCd CYCLE screen and set charge/discharge
• Press the Jog dial to save your choice and the number of cycles (B) flashes
cycle count parameters.
• Rotate the Jog dial to set the cycle count between 1 to 5
• Press the Jog dial to save the cycle count value
The battery can be put through a series of charge/discharge cycles using this
If no parameters are flashing, you can rotate the Jog dial to select another
program. Cycling Ni-Cd batteries can increase capacity and rejuvenate neglected
batteries. Discharge capacity and average battery voltage help you compare batter-
program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK.
ies for the best run time and power.
To start cycling, press and hold the Jog dial for 3 seconds.
NiCd CYCLE
CHG>DCHG
5
A
B
32
PB BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
to locate the PROGRAM SELECT Pb BATT screen. Press the Jog dial to select Pb.
Rotate the Jog dial to go to one of the control screens (CHARGE or DISCHARGE)
to do what your battery needs.
The nature of a Lead Acid or Sealed Lead Acid battery is very different from that of
Lithium, Ni-MH or Ni-Cd batteries. The output current of a Pb battery is lower than
other batteries relative to their capacities. Furthermore, lead acid batteries can't be
charged at a level greater than 1/10 their capacity.
For example, a 5000mAh lead acid battery can't be charged at a rate greater than
0.5A. For more details on the charge and discharge capabilities of your battery,
please refer to the charging data supplied by the battery manufacturer.
Correctly connect your Pb battery to the charger. Press the Jog dial and adjust
the charging parameters as needed. Press and hold the Jog dial (approximately 3
seconds) until the screen changes to start the battery check/charge sequence.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).
33
PB CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
to locate the PROGRAM SELECT Pb BATT screen. Press the Jog dial to go into
this menu.
Rotate the Jog dial to go to the Pb CHARGE screen and set charging parameters.
The charging amperage (A) can be set between 0.1 and 10.0A.
Pb CHARGE
0.1A
2.0V (1P)
A
CAUTION: The Ni-Cd program menus are to be used ONLY for the
34
charging and discharging of Ni-Cd battery packs. The charging of other
PB dISCHARGING
battery types using these programs will result in damage to the battery
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
or charger.
to locate the PROGRAM SELECT Pb BATT screen. Press the Jog dial to go into
CAUTION: Using a charge rate that is not compatible with the battery
this menu.
capacities may result in damage or malfunction of the charger or
Rotate the Jog dial to go to the Pb DISCHARGE screen and set discharging
batteries.
parameters. The discharging amperage (A) can be set between 0.1 and 5.0A.
A battery's capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
set from 2 to 20V.
Pb DISCHARGE
0.1A
2.0V (1P)
A
35
BATTERy MEMORy
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
to locate the PROGRAM SELECT BATT MEMORY screen. Press the Jog dial to
select BATT MEMORY.
Use this menu to create a battery profile. To reduce the time required to initiate a
charging or discharging cycle on a battery you regularly use, this charger has been
designed with the capability of storing up to 10 battery profiles that can be quickly
accessed and run at a later time.
• Rotate the Jog dial to identify a battery profile, 1 through 10
• Press the Jog dial to select battery profile 1
• Press the Jog dial so battery type flashes
• Rotate the Jog dial to select a battery type
• Press the Jog dial to save the battery type
Follow this process using the Jog dial to select, change, then save each param-
eter (battery voltage, charge current, discharge current, discharge voltage, Terminal
Voltage Control (TVC) and temperature cutoff). Then save the battery profile.
36
SySTEM SET
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to locate the PROGRAM SELECT SYSTEM SET screen. Press the Jog dial to select
SYSTEM SET.
Use this menu to set the "behind the scenes" operating parameters for this charger such as; Rest Time, Safety Timer, Capacity Cutoff, Key Beep/Buzzer, Input Power Low
Cutoff, External and Internal Temperatures, Load Factory Settings and Version.
a
REST TIME
Use this menu to set the Rest time during each step in a cycle.When a Ni-MH
or Ni-CD battery is cycled (charged, discharged and charged again) it will get
hot, therefore it is necessary to set a rest time interval during each step of the
process to make sure the battery and charger are completely cooled before
moving on to the next part of the cycle. Default time is 10 minutes, but this
can be set between 1 and 60 minutes. To select a value other than the default
parameter:
• Press the Jog dial to select Rest Time
• Press the Jog dial so the Rest Time value flashes
• Rotate the Jog dial to select Rest Time in Minutes
• Press the Jog dial to save the Rest Time value
• Rotate the Jog dial to select SAFETY TIMER
b
SAfETy TIMER
Use this menu to set a time limit for charging a battery. When a charge cycle
is started, a clock inside the charger will begin recording the elapsed charge
time. If the SAFETY TIMER function has been turned ON, the charger will stop
the charging process once this time limit has been reached to avoid damage
caused by over-charging the battery. This time value can be set between 1 and
720 minutes.
To select values other than the default parameters:
• Press the Jog dial so the ON/OFF value flashes
• Rotate the Jog dial to select ON or OFF
• Press the Jog dial to save the value
• Rotate the Jog dial to select the value for time
• Press the Jog dial to save the value
• Rotate the Jog dial to select Capacity Cutoff
c
CAPACITy CUTOff
Use this menu to set a capacity limit at which the charger will stop charging a
battery. When a charge cycle starts, the charger records the battery capacity.
When the Capacity Cutoff function is set at ON, the charger will stop charging at
the capacity limit to prevent battery damage. Capacity can be adjusted between
100 and 50,000mAh.
• Press the Jog dial so the ON/OFF value flashes
• Rotate the Jog dial to select ON or OFF
• Press the Jog dial to save the value
• Rotate the Jog dial to select the Capacity Cutoff value
• Press the Jog dial to save the value
• Rotate the Jog dial to select Key Beep/Buzzer
You may exit this menu at any time by pressing the Mode key to return to the main menus.
37
LI BATTERy VOLTAGE CHECKER OPERATION - USING THE BALANCE AdAPTER PORT
The Passport™ Ultra Duo charger has the capability to read and display the indi-
B
C
d
A. A Lead Acid battery pack is
vidual cell voltages of a Li-Po, Li-Fe or Li-Io battery. This voltage checking function
charging
Pb-6 0.4A 12.39V
can only be used when the charger is powered ON and not charging a battery.
B. B attery pack has 6 cells
A
CHG 022:43
01082
in series
To use the voltage checker, connect the balance port connector of your Li-Po, Li-Fe
or Li-Io battery to the balance adapter board connected to the Balance Circuit
f
E
Adapter Board Connector (C).
C. Charging at a rate of 0.4A (400mAh)
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
d. Voltage being applied to the battery is currently 12.39V
to locate the PROGRAM SELECT LI BATT METER screen. Press the Jog dial to
E. Present charge level of the battery is 1082mAh
select LI BATT METER.
f. Time elapsed since the charge process started is 22:43
In a few moments, the charger will begin to display the cell voltages of the battery
During charging, the Jog dial can be rotated counterclockwise to show several
in the following format:
parameter messages on the LCD screen, including: End Voltage, Capacity Cutoff,
Safety Timer Status, Temperature Cutoff and Input Power Voltage. The charger
3.70 3.70 0.00 V
signals when the charging (or discharging) process is complete (if Buzzer is set to
0.00 0.00 0.00 V
ON).
CAUTION: The Pb program menus are to be used ONLY for the charging
and discharging of Pb battery packs. The charging of other battery types
using these programs will result in damage to the battery or charger.
CAUTION: Using a charge rate that is not compatible with the battery
38
capacities may result in damage or malfunction of the charger or
USB ACCESSORy CHARGER OPERATION (COMPATIBLE WITH iPhone ANd iPod dEVICES)
batteries.
The Passport Ultra Duo charger has the capability to charge your iPhone, iPod or USB compatible device with the 1A USB charge port (E). To use the charging function,
simply connect a compatible charging device or cord into the charge port while the charger is powered ON. The internal USB charge port will provide up to 1A current at
5V DC.
39
To select values other than the existing parameters:
TROUBLESHOOTING GUIdE
• Press the Jog dial so the charge current value (A) flashes
LCD Screen Warning and Error messages shown below.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
• Press the Jog dial to save the charge current value and the battery voltage
During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger's LCD screen, make the recommended responses.
value (B) flashes
If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.
• Rotate the Jog dial to INCREASE OR DECREASE the battery voltage/cell count
REVERSE POLARITY
value (Pb batteries are 2.0V per cell, for a 6 cell battery this would be 2.0V x 6
cell = 12.0V)
CONNECTION BREAK
• Press the Jog dial to save the voltage
SHORT ERR
If no parameters are flashing, you can rotate the Jog dial to select another
program such as DISCHARGE.
INPUT VOL ERR
B
To start charging, press and hold the Jog dial for 3 seconds.
VOL SELECT ERR
BREAK DOWN
To select values other than the existing parameters:
BATTERY CHECK LOW VOLTAGE
• Press the Jog dial so the discharge current value (A) flashes
BATTERY CHECK HIGH VOLTAGE
• Rotate the Jog dial to INCREASE OR DECREASE the discharge current value
• Press the Jog dial to save the value and the cutoff voltage value (B) flashes
Battery Type
• Rotate the Jog dial to INCREASE OR DECREASE the cutoff voltage
Standard voltage (Volts per cell)
• Press the Jog dial to save the voltage value
Max. voltage (Volts per cell)
If no parameters are flashing, you can rotate the Jog dial to select another
Min. voltage (Volts per cell)
program such as CHARGE.
To start discharging, press and hold the Jog dial for 3 seconds
B
• Rotate the Jog dial to select SAVE PROGRAM
• Press the Jog dial to save the program
• Repeat this process to enter additional battery profiles
• Press the Mode key until you reach the 9 main menus
CAUTION: Increasing the TVC value beyond the default settings may result in a
shorter battery life and/or damage to the battery. Do not change the TVC value
unless you fully understand the effects TVC will have on your battery.
To Charge or Discharge a battery using the saved profile:
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial
to locate the PROGRAM SELECT BATT MEMORY screen. Press the Jog dial to
select BATT MEMORY.
• Rotate the Jog dial to identify the battery profile, 1 through 10.
• Press and hold the Jog dial for 3 seconds
• Rotate the Jog dial to choose the type of charge function you wish to perform
• Press and hold the Jog dial for 3 seconds to start
d
KEy BEEP/BUZZER
Use this menu to set the key beep and charger alarm buzzer at ON or OFF as
needed. We recommend that you keep the alarm ON so the alarm will sound
when charging is complete or if there is cause for alarm during charging.
To select values other than the default parameters:
• Press the Jog dial so the Key Beep ON/OFF value flashes
• Rotate the Jog dial to select ON or OFF
• Press the Jog dial to save the value
• Press the Jog dial so the Buzzer ON/OFF value flashes
• Rotate the Jog dial to select ON or OFF
• Press the Jog dial to save the value
• Rotate the Jog dial to select Input Power Low Cutoff
e
INPUT POWER LOW CUTOff
Use this menu to set the input voltage limit so an alarm will sound if the voltage
goes below the cutoff value. The voltage alarm value can be set anywhere from
10.0 to 11.0V.
To select a value other than the default parameter:
• Press the Jog dial so the voltage value flashes
• Rotate the Jog dial to select the voltage value
• Press the Jog dial to save the value
• Rotate the Jog dial to select External and Internal Temperatures
f
EXTERNAL ANd INTERNAL TEMPERATURES
By selecting the External and Internal Temperatures Screen you can view the
current temperatures of both the battery (external) and the charger (internal).
The optional temperature sensor (DYN5033) is required for external temperature
measurement.
g
RESET fACTORy SETTINGS
• Press the Jog dial to reset the charger to factory settings
• Press the Jog dial to select VERSION
h
VERSION
By selecting the Version Screen you can view the version (revision number) of the
software on your charger.
This example is for a 2S battery, so only the voltages for these two cells are
displayed. The data is presented in this format:
1–1
1–2
1–3 V
1–4
1-5
1–6 V
At this point, you can rotate the Jog dial to see a display of the overall battery
voltage as well as the individual high- and low-cell voltage values.
MAIN
08.20V
H4.104V
L4098V
You may exit this menu at any time by pressing the Mode key to return to the
main menus.
Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery
Make sure the power connections are correct for charging
Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.
Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct
input voltage.
Incorrect setting for cell in series count (pack voltage) of a lithium battery. Make charger settings match the battery pack label cell in series count
specifications or replace the battery.
Charger electronics require repair.
Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
Li-Po
Li-Io
Li-Fe
Ni-MH
Ni-Cd
Pb
3.70
3.60
3.30
1.20
1.20
2.00
4.20
4.10
3.60
1.60
1.60
2.45
3.00
3.00
2.00
1.00
0.85
1.75