Dynamite Prophet Plus II Manuel - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Dynamite Prophet Plus II. Dynamite Prophet Plus II 6 pages. Ac/dc powered peak detection fast charger for 4- to 8-cell ni-cd & ni-mh batteries
Également pour Dynamite Prophet Plus II : Manuel de l'utilisateur (2 pages)

Imprimer la page

1. 110V AC power cord

2. 12V DC power cord with alligator clips

3. Charge rates of 1, 2, or 4 amps

4. LED and beeper indicate when charge

is complete

5. Cooling fan

6. Tamiya-style connector

SupplyINg pOWER TO ThE ChaRgER

This charger can be powered by connecting it to a standard 110V wall outlet or by using the provided alliga-

tor clips to connect the charger to a 12V DC power source, such as a 12V hobby battery (HAN102), a 12 volt

power supply or an automobile battery.

CAUTION: Never connect the AC and DC input cords to an active power source at the same time. This

will void the warranty, cause product damage and possibly injure the user.

CAUTION: If you choose to power your charger with an automobile battery, never do so with the

automobile running as fluctuation in power can cause product malfunction and possibly injury

AC Power

To power the charger, use the attached standard electrical plug and plug into a standard 110V wall outlet.

NOTICE: Always consult collateral materials or Horizon Hobby before using with sources other than

standard 110V AC wall outlet.

fEaTuRES

Additional Features

• Receiver pack charge lead adapter included

• Charges 4- to 8-cell Ni-Cd or Ni-MH battery packs

• Limited 5-year warranty

• Advanced trickle charge

• Advanced peak detection circuitry

• Ni-Cd and Ni-MH compatible

DC Power

To power the charger, attach the included red (positive) alligator clip to the red (positive) terminal of the

12V power source. Attach the black (negative) alligator clip to the black (negative) terminal of the 12V

power source.

WARNING: Always make sure that you follow proper polarities at all times or electrical shock will occur.

Charging 6/7-Cell Ni-Cd or Ni-MH Car Packs

1. When power is supplied to the charger, the charger will beep, and the LED will flash once.

2. Connect the battery pack to the charger, and the charger will beep again, The LED will repeatedly blink

until you begin the charging process.

Note: For optimum performance, charge 8 cell packs using an AC power source.

3. Select the charge rate based on the batteries capacity rating. See "Charge Times" chart on Page 3.

4. Push the Start button to begin the charging process. The LED will be solid red during the

charging process.

5. Once the battery has peaked, the LED will flash, and the beeper will sound for 30 seconds. If the

battery is left connected after 30 seconds, the LED will continue to flash, and the beeper will sound

approximately every 90 seconds.

When the battery has peaked, the Prophet Plus II will automatically transition to Advanced Trickle Charge.

Charging 4- & 8-Cell Ni-Cd or Ni-MH Radio Packs

1. When power is supplied to the charger, the charger will beep, and the LED will flash once.

2. Connect the battery pack to the charger using the included RX charge adapter, and the charger will

beep again, The LED will repeatedly blink until you begin the charging process.

3. Select a charge rate of either 1 or 2 amps, depending on the receiver pack you are going to charge.

We recommend that you charge 600mAh or lower capacity receiver packs at 1 amp, while you may

charge higher capacity packs at 2 amps.

4. Push the Start button to begin the charging process. The LED will be solid red during the

charging process.

5. Once the battery has peaked, the LED will flash, and the beeper will sound for 30 seconds. If the

battery is left connected after 30 seconds, the LED will continue to flash, and the beeper will sound

approximately every 90 seconds.

When the battery has peaked, the Prophet Plus II will automatically transition to Advanced Trickle Charge.

Note: When you connect the charger to a power source, the charger will beep. The charger also beeps

when a battery has been successfully connected. The LED will illuminate to indicate the battery is

charging. Once the battery has peaked, the LED will flash, and the charger will beep repeatedly.

CAUTION: Never re-peak a warm battery as the overcharging can damage the products and possibly the

user.

WARNING: If at any time during the charge process the battery pack(s) become hot (over 140º F), unplug

the battery immediately and discontinue the charge process.