Galanz DWUK003W Manuel d'instruction de l'utilisateur - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction de l'utilisateur pour {nom_de_la_catégorie} Galanz DWUK003W. Galanz DWUK003W 14 pages.
Imprimer la page
Dishwasher Features
8
2
3
4
6
4．Prior to Using for the First Time
Before using your dishwasher for the first time:
A.
Loading the Salt into the Softener
B. Fill the rinse aid dispenser
C.Select appropriate detergent
A. Setting the Water Softener
The water softener is designed to remove minerals and salts from the water, which would have a
detrimental or adverse effect on the operation of the appliance. The higher the content of these
minerals and salts, the harder the water is. The softener should be adjusted according to the
hardness of the water in your area. Your local Water Authority can advise you on the hardness of
the water in your area.
Setting
The amount of salt dispensed can be set from H0 to H7.
Salt is not required at the set value H0.
1. Set the value which can be found in the water hardness table.
2. Close the door.
3. Switch on the "Power" switch.
4. Hold down " Delay" button and then press "Programme" button for 5 seconds. The buzzer sounds
one time and H.flashes on the digital display.(factory setting is H4)
4
Front View
1 Upper Basket
2 Spray Arms
3 Lower Basket
1
4 Water Softener
5 Cutlery Basket
5
6 Detergent Dispenser
7 Rinse Aid Dispenser
8 Fork Shelf
7
For optional performance
1. Set the value which can be found in the water
hardness table.
2. Close the door.
3. Switch on the power switch.
4. Hold down " Delay " button and press "Programme "
button for 5 seconds. The buzzer rings one
time and H.flashes on the digital display.
(factory setting is H4)
To change the setting:
1. Press " Delay " button.
Each time the button is pressed, the set value
increases by one level;when the value of H7 has
been reached, the display jumps back to H0(off).
2. Press " Programme" button. The chosen setting
has now been stored.
B. Loading the Salt into the Softener
Always use salt intended for using with dishwasher.
NOTE: If your model has no water softener, you may skip this section
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the
dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses salts specifically
designed to reduce lime and minerals from the water.
The salt container is located beneath the lower basket and should be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers! All other types of salt not specifically
designed for use in a dishwasher, especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is
liable for any damages caused.
Only fill with salt just before starting one of the complete washing programmes.
This will prevent any grains of salt or salty water, which may have been spilt, remaining on the
bottom of the machine for any period of time, which may cause corrosion.
After the first wash cycle the control panel light expires.
1
A. Remove the lower basket and then unscrew and remove the cap from the salt container.
B. If you are filling the container for the first time, fill 2/3 of its volume with water (around 500ml).
Water hardness table
Water hardness
Set value on
M g / L
the machine
Clark
Range
0-110
0-8
soft
H0
120-140
9-10
soft
H1
150-180
11-12
medium
H2
190-210
13-15
medium
H3
16-20
medium
220-290
H4
21-26
hard
H5
300-370
27-38
hard
H6
380-540
39-62
hard
H7
550-890
2
1
2
5