Galanz XQG60-A708E Manuel du propriétaire - Page 9
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Galanz XQG60-A708E. Galanz XQG60-A708E 11 pages.
Imprimer la pageCleaning the drawer housing
Use a bottle brush to remove detergent residues
inside the drawer housing.
Use pointed nose pliers to withdraw the plastic filter.
Clean, put back and secure. These filter should be
checked every 6 months or so, or more often if there
are frequent interruptions to the water supply.
The filter must be put back in place after cleaning.
1. Disconnect the machine from
2. Place a container under the pump.
the mains electricity supply and
Unscrew and remove the filter.
open the lower cover with a
screwdriver.
The filter should be cleaned every 2 months or so, or when there
is fault that the "Rinse" and "Spin" LEDs flicker.
Important:
If the machine is exposed to temperatures below 0°C, certain precautions
should be taken.
1. Turn off the water tap.
2. Unscrew the inlet hose.
3. Unhook the drain hose from the rear support and position the end of this
hose and that of the inlet hose in a bowl. Run the spin programme.
4. Disconnect the appliance.
5. Screw the inlet hose and reposition the drain hose.
6. When you intend to start the machine up again, make sure that the room
temperature is above 0°C.
3. Clean the filter carefully.
Problem
Error Code
Possible Cause
1. The water tap is not open.
The machine
2. The drain hose is put down.
"Spin" LED flickers.
fills overtime.
3. The water inlet valve is damaged.
1. The door is not locked well.
2. garment is caught between the
There is a Door
door and the seal.
"Rinse" LED flickers.
lock alarm.
3. The door lock is damaged.
4. The motor is damaged.
1. The drain hose is squashed
or kinked.
The machine
"Rinse" and "Spin" LEDs
2. The drain pump filter is block.
drains overtime.
flicker.
3. The drainage system pipes
are blocked.
1. The water inlet valve is damaged.
Water overflows
2. The connection between the
the machine.
"Washing" LED
water sensor and wire is not
/ Water sensor
flickers.
secure.
works abnormal.
3. The water sensor is damaged.
1. The connection between the
motor and wire is not secure.
The motor does
"Washing" and "Spin"
2. The motor is protected because
not work.
LEDs flicker.
of over-heat.
3. The motor is damaged.
1. The connection between the
There is a
heating tube and wire is not
"Washing" and "Rinse"
heating tube
secure.
LEDs flicker.
fault.
2. The heating tube is damaged.
1. The connection between the
There is a
temperature sensor and wire is
"Washing", "Rinse" and
temperature
not secure.
"Spin" LEDs flicker.
sensor fault.
2. The temperature sensor is damaged.
1. Open the water tap.
2. hook up the hose.
3. Change the water inlet valve.
1. Lock the door well.
2. Put the garment into the drum.
3. Change the door lock.
4. Change the motor.
1. Check the drain hose.
2. Clean the filter.
3. Check the drainage system
and clean it.
1. Change the water inlet.
2. Check the connection and ensure
it is secure.
3. Change the water sensor.
1. Check the connection and ensure
it is secure.
2. Check if the machine is overloaded.
Switch off the machine, and retry
when the motor becomes cool.
3. Change the motor.
1. Check the connection and ensure
it is secure.
2. Change the heating tube.
1.
Check the connection and ensure
it is secure.
2. Change the temperature sensor.